manualshive.com logo in svg

Matrix SPARSH VP710, User Manual, Page: 479 / 1046

Share
Download
Matrix SPARSH VP710 User Manual Download Page 479

Matrix SPARSH VP710 User Guide

471

The usage of video mail is the same as that of voice mail, the following takes voice mail as an example:

When receiving a new voice mail, the phone will play a warning tone.The power indicator LED will slowly flash red 
and the touch screen will prompt “n New Voice Mail(s)” where (“n” indicates the number of unread voice mails, e.g., 

176 New Voice Mail(s)) and display 

.

If the voice mail pop-up message box disappears, it won't pop up again unless the you receives a new voice mail or 
re-register the account that has unread voice mail(s).

•

You can configure the phone not to display the pop-up prompt, contact your system administrator for 
more information.

•

The icon 

 

on the status bar has a counter indicating the number of messages you haven’t heard 

yet.

Voice Mail Tone

Voice mail tone feature allows the IP phone to play a warning tone when receiving a new voice mail. You can 
customize the warning tone or select specialized tone sets (vary from country to country) for your IP phone. For 
more information, refer to 

“Tones”

.

Procedure

Voice mail tone can be configured using the using the configuration files or locally.

Configuration File

<MAC>.cfg

Configure whether to play a warning
tone when the IP phone receives a new
voice mail.

For more information, refer 

“Appendix 

D - Configuration Parameters”

.

 

Summary of Contents for SPARSH VP710























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments