Matrix SPARSH VP710 User Manual Download Page 475

Page: 475 / 1046

Matrix SPARSH VP710 User Guide

467

Logon Wizard

Logon wizard allows IP phones to provide the logon wizard during the first startup.

Logon wizard feature works only if there is no registered account on the IP phone.

Procedure

Logon wizard can be configured using the configuration files or locally.

To configure logon wizard feature via web user interface:

•

Click on

Features->General Information

Configuration File

<MAC>.cfg

Configure the logon wizard.

For more information, refer

“Appendix D - Configuration
Parameters”

Local

Web User Interface

Configure the logon wizard.

Navigate to

ttp://<phoneIPAddress>/servlet?m=

mod_data&p=features-actionurl&q=l

oad

Summary of Contents for SPARSH VP710























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for SPARSH VP710

Reviews:

Related manuals for SPARSH VP710

Brands by name

Popular brands

Matrix SPARSH VP710, User Manual

Search results

Summary of Contents for SPARSH VP710

Reviews:

Related manuals for SPARSH VP710

Brands by name

Popular brands