Home
/
Matrix
/
SPARSH VP710
/
User Manual

Matrix SPARSH VP710, User Manual, Page: 467 / 1046

Share

Page: 467 / 1046

Matrix SPARSH VP710 User Manual Download Page 467

Matrix SPARSH VP710 User Guide

459

IP Direct Auto Answer

IP direct auto answer allows IP phone to automatically answer an IP address call. IP direct auto answer works only
if allow IP call is enabled. For more information on allow IP call, refer to

“Allow IP Call”

Procedure

IP direct auto answer can be configured using the configuration files or locally.

To configure IP direct auto answer via web user interface:

•

Click on

Features->General Information

.

•

Select the desired value from the

IP Direct Auto Answer

list.

Configuration File

<MAC>.cfg

Configure IP direct auto answer.

For more information, refer

D - Configuration Parameters”

Local

Web User Interface

Configure IP direct auto answer.

Navigate to

:

http://<phoneIPAddress>/servlet?m

=mod_data&p=features-general&q

=load

«
...
465
466
467
468
469
...
»

Summary of Contents for SPARSH VP710























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments