Matrix SPARSH VP710 User Manual Download Page 150 | Manualshive

Page: 150 / 1046

background image

142

Matrix SPARSH VP710 User Guide

Auto-Logout Time

Auto-logout time defines a specific period of time during which the IP phones will automatically log out if you have
not performed any actions via web user interface. Once logging out, you must re-enter username and password for
web access authentication.

Procedure

Auto-Lougout Time can be configured using the configuration files or locally.

To configure the auto-logout time via web user interface:

•

Click on

Features->General Information.

Configuration File

<MAC>.cfg

Configure auto-logout time.

For more information, refer

D - Configuration Parameters”

Local

Web User Interface

Configure auto-logout time.

Navigate to

:

http://<phoneIPAddress>/servlet?m
=mod_data&p=features-general&q
=load

«
...
148
149
150
151
152
...
»

Summary of Contents for SPARSH VP710























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SPARSH VP710

Brand: Yealink Pages: 3

Yealink SIP-T20P

Brand: Yealink Pages: 2

Brand: Archos Pages: 40

Brand: Sagem Pages: 94

Brand: PCD Pages: 62

Brand: Macronix Pages: 65

Brand: Ultrative Pages: 97

Brand: IPRO Pages: 53

Brand: Wherify Pages: 37

Brand: Avaya Pages: 182

Brand: Nokia Pages: 20

Brand: GENERAL MOBILE Pages: 158

Brand: LG Pages: 106

Brand: Avvio Pages: 45

Brand: Samsung Pages: 2

Brand: Samsung Pages: 2

Brand: Samsung Pages: 2

Brand: Samsung Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands