background image

6

1

FOOT PLATFORM STARTING POSITION

Grasp handle, squeeze pin, push or pull platform 

to desired start position, release pin.
Allows the user to adjust the starting position of 

the footplate.  The user pulls the pin and slides 

the platform closer or further away to achieve 

the desired knee flexion at the start position. 

1

2

3

4

4

Stack Release

To release carriage from the weight stack, grasp handle 

under seat and rotate to the unlocked position    .
This disengages the weight stack from the 

carriage allowing the user to perform a body 

weight or band resistance only leg press.  

2

Foot Platform Adjustment 

– Therapist Position

To adjust the foot platform forward or back step down on 

the adjustment pad, position platform and then release.
Allows the Therapist to adjust the starting position of the 

footplate.  The therapist steps down on the adjustment 

pad, slides the platform closer or further away from 

the user to achieve the desired knee flexion at the start 

position, and then releases the adjustment pad. 
*It is easier to do when standing at the 

rear of the unit versus the side.

3

Foot Rest

Grasp center of foot rest, pull out to full extension.
Gives the user a place to rest a foot 

while doing 1-legged exercises.
The foot rest is not intended to support the 

user’s complete body weight. Do not apply 

more than 300 lbs (136 kg) to the foot rest.

ADJUSTMENT POINTS

ENGLISH

The seat side handles are intended to aid the user to remain 

in the seat while doing the exercise. The handles are not 

intended to support the user’s complete body weight. Do not 

apply more than 300 lbs (136 kg) of force to the handles.

Summary of Contents for MD-S70





















Reviews: