Matrix Switch Corporation MSC-XDM2000L Product Manual Download Page 4

Page: 4 / 64

MSC-XDM2000L Product Manual

Table of Contents

1 Getting Started...................................................................................................................................................7

1.1 Device Connections.....................................................................................................................................7
1.2 Video I/O Boards..........................................................................................................................................8

1.2.1 Installing Video I/O Boards..................................................................................................................9
1.2.2 SFP Modules.......................................................................................................................................10

1.3 Powering Up The Device...........................................................................................................................11
1.4 Front Panel Button Interface......................................................................................................................11

1.4.1 Audio Breakaway...............................................................................................................................12

1.5 Web Page Interface.....................................................................................................................................12

1.6 Network Planning.......................................................................................................................................14

1.6.1 Installation Example...........................................................................................................................15

1.7 Advanced Panel Configuration..................................................................................................................15

2 Web page interface...........................................................................................................................................16

2.1 Overview....................................................................................................................................................16
2.2 Routing Tab................................................................................................................................................16

2.2.1 Changing a connection.......................................................................................................................17
2.2.2 Loading a preset.................................................................................................................................17

2.3 Presets Tab..................................................................................................................................................17

2.3.1 Loading Work Matrix from a source target........................................................................................18
2.3.2 Saving Work Matrix to a target..........................................................................................................18
2.3.3 Usage scenarios..................................................................................................................................18

2.4 Labels Tab..................................................................................................................................................18
2.5 Config Tab..................................................................................................................................................19

2.5.1 System Settings..................................................................................................................................20
2.5.2 Network Settings................................................................................................................................20
2.5.3 Button Panel Settings.........................................................................................................................21

2.6 Command Tab............................................................................................................................................22

3 Mascot Control Protocol.................................................................................................................................23

3.4.1 Command Names...............................................................................................................................25

3.5 Response Format........................................................................................................................................25
3.6 Command Arguments.................................................................................................................................26
3.7 System Parameters.....................................................................................................................................27

3.7.1 System Parameter Table.....................................................................................................................28

Page 4 of 64

www.matrixswitch

corp.com

Summary of Contents for MSC-XDM2000L

































































Search results

Summary of Contents for MSC-XDM2000L

Reviews:

Matrix Switch Corporation MSC-XDM2000L, Product Manual, Page: 4 / 64

Search results

Summary of Contents for MSC-XDM2000L

Reviews: