background image

MCL16RS  5 07/05/18

MCL16RS 16V RECIPROCATING SAW

SAVE THESE INSTRUCTIONS!

SAFETY INSTRUCTIONS FOR BATTERY 

CHARGER AND BATTERY PACK

DANGER! READ CAREFULLY
120 Volts present at charging terminal. Absolutely DO NOT 
probe with conductive objects.

1 .   CAREFULLY READ AND UNDERSTAND THESE INSTRUCTIONS 
 

This manual contains critical safety and operating 

 

instructions for the tool, battery charger, and battery .

2 .   Before using battery charger, read all instructions and   
 

cautionary markings on (1) battery charger, (2) battery,  

 

and (3) product using battery .

3 .   CAUTION - To reduce risk of injury, charge only MATCO 
 

rechargeable batteries marked on the charger label .  

 

Other types of batteries may burst causing personal  

 

injury and damage .

4 .   Do not expose charger to rain or snow .
5 .   Use of an attachment not recommended or sold by Matco  
 

or the battery charger manufacturer may result in a risk of  

 

fire, electric shock, or injury to persons .

6 .   To reduce risk of damage to electric plug and cord, pull by  
 

plug rather than cord when disconnecting charger .

7 .   Make sure cord is located so that it will not be stepped on,  
 

tripped over, or otherwise subjected to damage or stress .

8 .   An extension cord should not be used unless absolutely 
 

necessary . Use of improper extension cord could result in 

 

a risk of fire and electric shock . If extension cord must be 

 

used, make sure:

 

a .   That pins on plug of extension cord are the same   

 

    number size, and shape as those of plug on charger;

 

b .   That extension cord is properly wired and in good   

 

    electrical condition;

 

c .   That wire size is at least as large as the one specified  

 

    in the table below .

 

Table 1: RECOMMENDED MINIMUM AWG SIZE FOR    

 

EXTENSION CORDS FOR BATTERY CHARGERS

Length of Cord (Feet)  

25   50   75   100  150

AWG Size of Cord  

18   18   16   14    12

9 .   Do not operate charger with damaged cord or plug -    
 

replace them immediately .

10 .  Do not operate charger if it has received a sharp blow,  
 

been dropped, or otherwise damaged in any way;  

 

take it to a MATCO AUTHORIZED service facility .

11 .  Do not disassemble charger or battery cartridge; 
 

take it to your MATCO AUTHORIZED distributor service   

 

facility .  Incorrect reassembly may result in a risk  

 

of electric shock or fire .

12 .  To reduce risk of electric shock, unplug charger from   
 

outlet before attempting any maintenance or cleaning .  

 

Turning off controls will not reduce this risk .

13 .  The battery charger is not intended for use by young    
 

children or infirm persons without supervision .

14 .  Young children should be supervised to ensure that they  
 

do not play with the battery charger .

OPERATIONAL GUIDELINES  

FOR BATTERY CHARGER AND 

BATTERY PACK

1 .   Do not attempt to use a step-up transformer, an engine  
 

generator or DC power receptacle .

2 .   Do not allow anything to cover or clog the charger vents .
3 .   Always cover the battery terminals with the box or cover  
 

when the battery cartridge is not used .

4 .   Do not short the battery cartridge:
 

(1)  Do not touch the terminals with any conductive    

     material .
 

(2)  Avoid storing battery cartridge in a container  

 

    with other metal objects such as nails, screws,  

 

    coins, etc .

 

(3)  Do not expose battery cartridge to water 

 

    or rain . A battery short can cause a large current flow,  

 

    overheating, possible burns and even a breakdown .

5 .   Do not store the tool and Battery Cartridge in locations  
 

where the temperature may reach or exceed  

 

50°C (122°F) .

6 .   Do not incinerate the Battery Pack even if it is  
 

severely damaged or is completely worn out .  

 

The battery cartridge can explode in a fire .

7 .   Be careful not to drop, shake or strike battery  
 

as it will affect the capacity and may void warranty .

8 .   Do not charge inside a box or container of any kind .  
 

The charger and battery are ventilated devices and 

 

must NOT be placed next to a heat source or in 

 

exposure to radiating heat . 

9 .  Place charger on a solid and sturdy surface as there are  
 

vents on the bottom side of the charger .

10 .  Always unplug the charger from the power supply when a  
 

charging sequence is not taking place . 

FAILURE TO OBSERVE THESE WARNINGS COULD RE SULT IN IN JU RY.

WARNING

Summary of Contents for MCL16RS





















Reviews: