Page 1
PRODUCT INFORMATION:
INTENDED USE OF THE TOOL
WARNING
DO NOT DISCARD – GIVE TO USER
The manufacturer warrants this product to the original
user against defective material or workmanship for
either a period of lifetime, or consumable (drill bits 1/4"
and below only). Ask your distributor for more details.
The manufacturer reserves the right to determine
whether the part(s) failed because of defective material,
workmanship or other causes. Failures caused by
accident, alteration or misuse are not covered by this
warranty.
Replacements under warranty also carry a Lifetime
Warranty. The rights under this warranty are limited to
the original user and may not be transferred to
subsequent owners.
The warranty is in lieu of all other warranties, expressed
or implied, including warranties of merchantability and
fitness for a particular purpose.
Some states do not allow the exclusion or limitations of
incidental or consequential damages, so the above
limitations may not apply to you.
(M) MIXED WARRANTY
(Lifetime and Consumable)
1812422-14
124 PIECE AUTO MASTER
TAP AND DIE SET
124MATDS
When unpacking, check the parts diagram and part
number listing on page 16-17 to make sure all parts are
included. If any parts are missing or damaged, please
call your distributor.
BEFORE USE
Study, understand and follow all instructions provided
with this product. Read these instructions carefully
before installing, operating, servicing or repairing this
tool. Keep these instructions in a safe, accessible place.
This tap and die tool set is designed for cutting male and
female threads of the thread pitches included in the kit
using the drill bits provided in this set our other high
quality appropriate size drill bits. This set is only suitable
for experienced technicians. Tap only appropriately sized
holes (see page 2); undersized holes will cause damage
to the tool or work piece. Do not use this tool outside of
the designed intent. Never modify the tool for any other
purpose or use.
Made in Taiwan
to Matco specifications
PAT. No. US8616095 B2
Caution: To help prevent personal injury
• Use of this product can expose you to chemicals
including ethylene glycol, gasoline vapors and engine
exhaust, which are known to the State of California to
cause cancer, birth defects, or reproductive harm. For
more information, visit www.P65Warnings.ca.gov.
Always wear ANSI approved safety equipment, safety
glasses and clothing when using this product. Study,
understand, and follow all instructions provided with
this product. Failure to read and follow all warnings
and operating instructions may result in damages and
serious injury or death.
• Always wear ANSI approved goggles when using this
product. (Users and Bystanders).
• Never use this tool for any application other than for
which it was designed.
• Only use accessories designed for this tool.
• Never alter or modify this tool in any way.
• Improper operation and/or maintenance of the tool,
modification of the tool, or use of the tool with
accessories not designed for it could result in serious
injury or death.
• Always select the correct accessories of the correct
size and design for the job that you are attempting to
perform.
• Always work in a clean, safe, well-lit, organized and
adequately equipped area.
• Do not begin repairs without assurance that vehicle is
in secure position, and will not move during repair.
WARNING
• Includes extractors and drill bits in the following sizes:
Extractor #1, #2, #3, #4, #5.
Drill bit No. 3, 7, 9, 16, 19, 20, 21, 25, 29, 30, 36, 39, 43,
Letter B, F, H, I, J, Q, O, R, S, T, U, Z and
Fractional sizes 5/64", 7/64", 5/32", 1/4", 19/64", 5/16",
21/64", 3/8", 25/64", 13/32", 27/64", 7/16", and 29/64".
• Includes taps and dies in the following sizes:
M3x0.5, M3x0.6, M4x0.7, M4x0.75, M5x0.8, M5x0.9,
M6x1.0, M7x1.0, M8x1.0, M8x1.25, M9x1.0, M9x1.25,
M10x1.0, M10x1.25, M10x1.5, M11x1.5, M12x1.25,
M12x1.5, M12x1.75, 1/8BSP, 4-40, 6-32, 8-32, 10-24,
10-32, 12-24, 1/4-20, 1/4-28, 5/16-18, 5/16-24, 3/8-16,
3/8-24, 7/16-14, 7/16-20,1/2-13, 1/2-20, 1/8NPT
