Masterweld MW1901 Instruction Manual Download Page 8

Page 8 of 34

MW1901

©| AES Industrial Supplies Ltd | 2019 all rights reserved

reproduction of this manual, even partial, is forbidden.

PICTOGRAMS CONCERNING THE STATE OF THE MACHINE

Pictograms inside a square/rectangle provide INFORMATION.

Symbol

Descrip�on

Machine off:

with hydraulic or electric power supply disconnected.

Machine on:

with hydraulic or electric power supply connected and in safe stop condi�on with open

mobile protective devices (specifying which); JOG disabled; fixed protection devices closed.

Machine on:

with hydraulic or electric power supply connected and in safe stop condi�on with

emergency mushroom bu�on pressed or other control with the same func�on ac�vated, posi�oned
near the interven�on area (specifying the mushroom bu�on or the device to be used).

Machine moving:

in automa�c mode, with mobile protec�on devices closed, the relevant interlocking

devices activated, and the fixed protec�on devices closed.

Machine moving:

in JOG mode, with mobile protec�on devices closed, the relevant interlocking

devices activated, and the fixed protec�on devices closed.

Machine moving:

in JOG mode, with one or more mobile protection devices, that can be disabled,

open (specifying which) with the relevant interlocking devices activated and fixed protection devices
closed.

Machine on:

in stand-by and wai�ng for func�onal consent to start (e.g. presence of product), mobile

protec�on devices closed with safety device closed, and fixed protec�on devices closed.

Table 0 - 4.2

Summary of Contents for MW1901



































Reviews: