background image

R

EAD AND

F

OLLOW

A

LL

I

NSTRUCTIONS

, W

ARNINGS

&

C

AUTIONS

B

EFORE

U

SING

T

HIS

B

ATTERY

S

WEEPER

P

AGE

1

The purpose of this manual is to inform
the operator of the basic operating and
safety procedures that must be followed
when operating, adjusting and maintaining
the sweeper. The machine has been
developed and manufactured to ensure an
excellent performance and the utmost
comfort and ease of operation in a variety
of working conditions.

This sweeper will afford you many years of
trouble-free operating satisfaction, provid-
ed it is given proper care. All parts have
passed rigid quality control standards
prior to being assembled to produce the
finished product. Prior to packaging, the
sweeper was again inspected for assur-
ance of flawless assembly. 

Your sweeper is protectively packed to
prevent damage in shipment. We recom-
mend that upon delivery, unpack the

sweeper and inspect it for any possible
damage. Only a visual examination will
reveal damage that may have occurred. 

If damage is discovered, immediately notify
the transportation company that delivered
your sweeper. As a shipper, we are unable
to report claims for concealed damage.
You must originate any claims within 5
days.

This manual is for your protection and
information. 

PLEASE READ CAREFULLY

since failure to follow precautions could
result in discomfort or injury. 

Read this manual completely before
operating this sweeper. It is important to
follow all instructions in the manual to
prevent the possibility of injury or dam-
age to the user and/or sweeper.

S

AFETY

O

PERATION

&

M

AINTENANCE

M

ANUAL

D

EBRIS

M

ASTER

28” & 36”

B

ATTERY

& G

AS

O

PERATED

S

WEEPERS

This unit is intended for commercial use. 

28” & 36” Sweeper - PN 447404 -Printed in USA  08/22/07

R

EAD

A

LL

I

NSTRUCTIONS

B

EFORE

O

PERATING

T

HIS

S

WEEPER

Summary of Contents for debrismaster













Reviews: