3
RULES FOR SAFE OPERATION
KNOW THE TOOL
To operate this tool safely, carefully read this Owner’s Manual and all labels
affixed to the Compound Mitre Saw before using it, and follow all instructions
contained therein. Keep this Manual for future reference.
IMPORTANT
This tool should only be serviced by a qualified service technician.
READ ALL INSTRUCTIONS THOROUGHLY
SAFETY PRECAUTIONS FOR LASERS
This Mitre Saw has a built-in
laser light. The laser is Class
IIIa, and emits a maximum
output power of 2.5 mW at
635-655 nm wavelengths.
These lasers do not normally
present an optical hazard.
However, DO NOT stare at the
beam, because this can cause
flash blindness.
CAUTION:
The following label appears on the tool. It indicates the location
from which the saw emits the laser light. BE AWARE of the laser-light location
when using the tool. Always make sure that any bystanders in the vicinity are
made aware of the dangers of looking directly into the laser.
•
Do not
remove or deface any product labels. Removing product labels
increases the risk of exposure to laser radiation.
•
The laser beam can be harmful to the eyes.
Always avoid direct eye
exposure.
•
Do not
look directly into the laser-beam-output aperture during operation.
•
Do not
project the laser beam directly into the eyes of others.
•
Turn the laser on
only
when making cuts. The laser on the Mitre Saw is not a
toy.
Always
keep it out of the reach of children. The laser light emitted from
this device
should never
be directed toward any person for any reason.
•
Be sure
that the laser beam is aimed at a workpiece that does not have a
reflective surface (e.g.: wood or a rough-coated surface).
MC-55-6896-2
10" Single Bevel Sliding Mitre Saw Labels
635-655 nm Output: ≤ 2.5 mW Class llla Laser Product
Complies with 21 CFR parts 1040.10 and 1040.11
635 à 650 nm. Puissance de sortie : ≤ 2,5 mW. Produit à laser de
classe llla. Conforme aux normes des paragraphe 1040.10 et 1040.11
du code 21 des règlements fédéraux américains (CFR) de la FDA.
LASER RADIATION. DO NOT STARE INTO BEAM.
RAYONNEMENT LASER. Ne regardez pas directement
le faisceau.
CAUTION
r
ATTENTION
AVOID EXPOSURE
t
ÉVITEZ TOUTE EXPOSITION
Laser radiation is emitted through this aperture.
Le rayonnement laser émane de cette ouverture.
10" Sliding Compound Mitre Saw
Scie à onglets mixtes coulissante de 10 po
55-6896-2
MADE IN CHINA/FABRIQUÉ EN CHINE
IMPORTED BY/IMPORTÉ PAR MASTERCRAFT CANADA, TORONTO CANADA M4S 2B8
Motor: / Moteur :
120 V AC 60 Hz 15 A / C.A. 120 V 60 Hz 15 A
No-load speed: / Vitesse à vide : 5500 /min / 5 500 tr/min
Serial No.: / N
o
de série :
WARNING:
For your own safety, read instruction manual before operating mitre saw. Wear
eye protection. Keep hands out of path of saw blade. Do not operate saw without
guards in place. Do not perform any operation freehand. Never reach around saw
blade. Turn off tool and wait for saw blade to stop before moving workpiece or
changing settings. Unplug tool before changing blade or servicing. Do not expose
to rain or damp locations. When servicing, use only identical replacement parts.
AVERTISSEMENT :
Par mesure de sécurité, lisez le guide d’utilisation à fond avant de vous servir de
l’outil. Portez des lunettes de sécurité. Gardez les mains éloignées de la lame.
N’utilisez pas la scie sans que le protège-lame soit en place. N’effectuez aucun
travail à main levée. Ne passez pas la main devant la lame. Éteignez la scie et
attendez que la lame arrête de tourner avant de déplacer la pièce ou d’effectuer
des réglages. Débranchez l’outil avant de remplacer la lame ou d’effectuer
l’entretien. N’exposez pas cet outil à la pluie et ne l’utilisez pas dans des endroits
humides. Lors de l’entretien, utilisez seulement des pièces de rechange
identiques.
Summary of Contents for 55-6896-2
Page 26: ...26 Exploded View ...
