MasterCraft 055-4500-6 Instruction Manual Download Page 18

3-Year Limited Warranty 

This Mastercraft product is guaranteed for a period of 

3 years

 from the date of original retail purchase against

defects in workmanship and materials, except for the following component:
Component A: Accessories, which are guaranteed for a period of 1-year from the date of original retail
purchase against defects in workmanship and materials.
Subject to the conditions and limitations described below, this product, if returned to us with proof of purchase
within the stated warranty period and if covered under this warranty, will be repaired or replaced (with the
same model, or one of equal value or specification), at our option. We will bear the cost of any repair or
replacement and any costs of labour relating thereto.

These warranties are subject to the following conditions and limitations:

a. a bill of sale verifying the purchase and purchase date must be provided;

b. this warranty will not apply to any product or part thereof which is worn or broken or which has become inoperative due
    to abuse, misuse, accidental damage, neglect or lack of proper installation, operation or  maintenance (as outlined in
    the applicable owner’s manual or operating instructions) or which is being used for industrial, professional, commercial
    or rental purposes;

c. this warranty will not apply to normal wear and tear or to expendable parts or accessories that may be supplied with the
    product that are expected to become inoperative or unusable after a reasonable period of use;

d. this warranty will not apply to routine maintenance and consumable items such as, but not limited to, fuel, lubricants,
    vacuum bags, blades, belts, sandpaper, bits, fluids, tune-ups or adjustments;

e. this warranty will not apply where damage is caused by repairs made or attempted by others (i.e. persons not
    authorized by the manufacturer);

f.  this warranty will not apply to any product that was sold to the original purchaser as a reconditioned or refurbished
    product (unless otherwise specified in writing);

g. this warranty will not apply to any product or part thereof if any part from another manufacturer is installed therein or
    any repairs or alterations have been made or attempted by unauthorized persons;

h. this warranty will not apply to normal deterioration of the exterior finish, such as, but not limited to, scratches, dents,
    paint chips, or to any corrosion or discolouring by heat, abrasive and chemical cleaners; and

i.  this warranty will not apply to component parts sold by and identified as the product of another company, which shall
    be covered under the product manufacturer’s warranty, if any.

Additional Limitations

This warranty applies only to the original purchaser and may not be transferred. Neither the retailer nor the manufacturer
shall be liable for any other expense, loss or damage, including, without limitation, any indirect, incidental, consequential
or exemplary damages arising in connection with the sale, use or inability to use this product.

Notice to Consumer

This warranty gives you specific legal rights, and you may have other rights, which may vary from province to province.
The provisions contained in this warranty are not intended to limit, modify, take away from, disclaim or exclude any
statutory warranties set forth in any applicable provincial or federal legislation.

This product is not meant for industrial or commercial purposes. This product is for household

projects. Read manual carefully.

Made in China

Imported by Mastercraft Canada Toronto, Canada M4S 2B8

 

 

34

WARRANTY

model no. 055-4500-6  |  contact us 1-800-689-9928

Summary of Contents for 055-4500-6



















Reviews: