manualshive.com logo in svg

MasterCraft 054-8255-8, Instruction Manual

Share
Download
MasterCraft 054-8255-8 Instruction Manual Download Page 17

headline bars

continuation tabs

notes

warnings

headline bars

continuation tabs

notes

warnings

headline bars

continuation tabs

notes

warnings

17

TROUBLESHOOTING

Problem

Possible Causes

Solution

The motor does not start.

The battery is depleted.

Charge the battery pack.

The battery is overloaded.

Decrease the load on the tool 
and restart the tool.

The battery is overheated.

Cool the battery and restart 
the tool.

The blade binds, jams, or burns 
the wood.

The blade is dull.

Replace the blade.

An improper blade is being 
used.

Replace the blade.

The blade is warped.

Replace the blade.

The saw vibrates or shakes.

The blade is damaged.

Replace the blade.

The blade is loose.

Remove the blade and reinstall 
it.

The base shoe is loose during the 
operation.

Two locking screws of the base 
shoe are not fully tightened.

Fully tighten two locking 
screws. Refer to the “BASE 
SHOE ADJUSTMENT” part for 
detailed operation.

If the problem remains unsolved after performing the checks described above, call the toll-free helpline 
at 1-800-689-9928.

•   

TROUBLESHOO

TING

Summary of Contents for 054-8255-8

























Reviews:

No comments

Brands by name

Popular brands

Load more brands