MasterCraft 046-0265-2 Instruction Manual Download Page 31 | Manualshive

Page: 31 / 55

MasterCraft 046-0265-2 Instruction Manual Download Page 31

headline bars

continuation tabs

notes

warnings

31

CONNECT THE

OPENER T

O

POWER

headline bars

continuation tabs

notes

warnings

CONNECT THE OPENER TO POWER

Connect AC Power

Plug motor unit into grounded outlet. If a grounded outlet
is not available, contact a qualified electrician to install
a proper outlet. DO NOT ACTIVATE THE OPENER UNTIL
INSTRUCTED.

Permanent Wiring/Remove Cover

Be sure the power cord is unplugged. Remove the screws
from the cover of the opener.

Permanent Wiring -

Remove the Power Cord

WARNING

If permanent wiring is required by your local code, have a licensed electrical contractor follow
the procedures outlined in this manual. Disconnect power to the circuit before removing
cover.
• Be sure power is not connected to the opener and disconnect power to circuit before

removing cover to establish permanent wiring connection.

• Garage door installation and wiring must be in compliance with all local electrical and

building codes.

• Never use an extension cord, 2-wire adaptor, or change plug in any way to make it fit

outlet. Be sure the opener is grounded.

• The opener has a grounded type plug for your protection and only fits into a grounding

type outlet. Do not change the plug in any way.

FPO

«
...
29
30
31
32
33
...
»

Summary of Contents for 046-0265-2
























































Reviews:

No comments