2
2
www.mastercool.com
File Management
Browse images from the micro SD card
Note: If you want to manage images, please use the USB
cable to connect the device and the computer)
Settings
Emissivity
The default emissivity is 0.95, or select other default emissivity:
Blackbody: 1.0,
Matt: 0.95, Semi-matt: 0.8, Semi-glossy:
0.6, Glossy: 0.3
Select Set Value to adjust the emissivity (0.1 to 1, in 0.01 steps)
HAL
When the reading is outside the High Alarm (HAL) or Lo Alarm
(LAL) limit, the reading (HAL: red texts, LAL: blue texts) shown
at the top left corner of the screen will flash with two short
beep sounds constantly.
Select
Set HA
temp or
Set LA
temp to adjust the limits or
select ON/OFF to turn on/off the alert.
LAL
Save file as Save the file as
photograph
or
record
Auto off
The default setting is “Auto off 1 min”, you can select other de-
fault values:
5, 10, 20 minutes or “No auto off”
. Manually power
off the device by pressing Power [ ] key (2) for 3 seconds.
Target
distance
The maximum distance between the thermal imaging camera
and the target:
1m, 2m or 3m
Languages Select:
English/French/Spanish/Portuguese/German/
Dutch/Italian/Traditional Chinese/Simplified Chinese
Set time
and date
Set the date and time in
MM/DD/YYYY
(month/day/year) and
HH/MM/SS
(hour/minute/second) formats.
STORAGE & CLEANING
The thermal imaging camera should be stored at room temperature. The sensor lens is
the most delicate part of the thermometer. The lens should be kept clean at all times, care
should be taken when cleaning the lens using only a soft cloth or cotton swab with water
or medical alcohol. Allowing the lens to fully dry before using the thermometer. Do not
submerge any part of the thermometer.
BATTERIES
The thermometer incorporates visual low battery indication as follows:
O
O
p
p
e
e
r
r
a
a
t
t
i
i
n
n
g
g
M
M
a
a
n
n
u
u
a
a
l
l
f
f
o
o
r
r
T
T
I
I
M
M
0
0
3
3
T
T
h
h
e
e
r
r
m
m
a
a
l
l
I
I
m
m
a
a
g
g
e
e
r
r
C
C
a
a
m
m
e
e
r
r
a
a
The thermal imager camera can measure from -20~250°C (-4~482°F) and displays the thermal image and temperature.
Furthermore, thermal images can be saved to a micro SD card. Transferring images to the software is included for image report
generation from these saved images.
OPERATION
1.
Power on
Press Mode Key (
2
) or Trigger (
10
) to power on the unit.
2.
Taking a thermal image and temperature
After power on, simply aim the thermal imager camera at the measure target with Lens
(
9
) and get the thermal image and temperature immediately. Please make sure the
target area is within the field of view.
Note: There are three cursors on the screen. The cross sign shows the temperature of
the object located in the middle of the screen. Other two moving cursors indicate the
highest and lowest temperatures in the thermal image.
3.
Save thermal images
Press Trigger (
10
) to save the thermal image to the micro SD card, press Up Key (
3
) or
Down Key (
4
) to show the saved images. Press Mode Key (
2
) again to return to the
measurement screen.
4.
Color palettes
Press Color Palette Key (
6
) to select the color palette (4 selectable color palettes) to view thermal images.
Ironbow
Rainbow
High contrast
Grayscale
5.
C/°F/K
Press Unit Key (
5
) for C
°F or K transferred.
6.
Power off
Press Mode Key (
2
) for more than 5 sec. to power off the unit. Auto power off time is around 30 sec..
FUNCTIONS
Press Mode Key (
2
) for scrolling more display functions, then press Up key (
3
) or Down key (
4
) to change the
functions, then press Trigger (
10
) to confirm it.
Emissivity
The default emissivity is 0.95, or select other default emissivity: Matt:0.95, Semi-matt:0.8, Semi-glossy:0.6,
Glossy:0.3
Select Set value to adjust the emissivity (0.1 to 1 step .01).
HAL
You can select Set Min temp or Set Max item to adjust the High Alarm (HAL) or Lo Alarm (LAL) limits
(step .1).
LAL
Language
Selectable Chinese or English.
Backlight
Selectable 5 levels of brightness.
Set Time
Set the date and time in MM/DD/YYYY (month/day/year) and HH/MM/SS (hour/minute/second) formats.
Time stamp
Turn on Time stamp to save thermal images with real-time stamp.
Turn off Time stamp to hide date and time on stored thermal images.
Erase Image
Select Yes, All image! to clear all stored thermal images.
Reset
Select Reset to recover the factory setting data.
Set parameter
Select Use Median Value
to reduce noise in an image.
Select No Filter
to display real image noise.
STORAGE & CLEANING
It should be stored at room temperature. The sensor lens is the most delicate part of the thermometer. The lens should be kept
clean at all times, care should be taken when cleaning the lens using only a soft cloth or cotton swab with water or medical alcohol.
Allowing the lens to fully dry before using the thermometer. Do not submerge any part of the thermometer.
BATTERIES
The thermometer incorporates visual low battery indication as follows:
‘Battery OK’: measurements
are possible
‘Battery Low’: battery needs to be
replaced, measurements are still possible
‘Battery Exhausted’: measurements are
not possible
When the ‘Low Battery’ icon indicates the battery is low, the battery should be replaced immediately with AA, 1.5V batteries.
Please note: It is important to turn the instrument off before replacing the battery otherwise the thermometer may malfunction.
Dispose of used battery promptly and keep away from children.
SPECIFICATION
Thermal Image Resolution
32*31
Measurement Range
-20~250°C (-4~482°F)
Accuracy (Tamb=20~26°C)
2% of reading, or 2°C(4°F) whichever is greater
Thermal Sensitivity
0.1°C
Frame Rate
9Hz
Field of View
40*40 deg
Emissivity Range
0.95 default – adjustable 0.1 to 1 step .01
Focus
Focus free
LCD (inch)
2.8
LCD Type
Color
Image Storage
Stores up to 60000 images/GB,
Bitmap (BMP) file format.
Memory Type
Support 8G micro SD card
Sensor Filter (um)
8~14um
Interface
USB
Battery Type
AA*4
Battery Life (hr)(backlit)
6
Dimensions
94.65 x 74.03 x 233.68mm (3.73 x 2.91 x 9.20 inch)
Weight
411 grams(14.5 oz) including batteries (AA*4pcs)
EMC/RFI: Readings may be affected if the unit is operated within radio frequency electromagnetic field strength of approximately 3 volts per
meter, but the performance of the instrument will not be permanently affected.
* IP54 Splash Proof
O
O
p
p
e
e
r
r
a
a
t
t
i
i
n
n
g
g
M
M
a
a
n
n
u
u
a
a
l
l
f
f
o
o
r
r
T
T
I
I
M
M
0
0
3
3
T
T
h
h
e
e
r
r
m
m
a
a
l
l
I
I
m
m
a
a
g
g
e
e
r
r
C
C
a
a
m
m
e
e
r
r
a
a
The thermal imager camera can measure from -20~250°C (-4~482°F) and displays the thermal image and temperature.
Furthermore, thermal images can be saved to a micro SD card. Transferring images to the software is included for image report
generation from these saved images.
OPERATION
1.
Power on
Press Mode Key (
2
) or Trigger (
10
) to power on the unit.
2.
Taking a thermal image and temperature
After power on, simply aim the thermal imager camera at the measure target with Lens
(
9
) and get the thermal image and temperature immediately. Please make sure the
target area is within the field of view.
Note: There are three cursors on the screen. The cross sign shows the temperature of
the object located in the middle of the screen. Other two moving cursors indicate the
highest and lowest temperatures in the thermal image.
3.
Save thermal images
Press Trigger (
10
) to save the thermal image to the micro SD card, press Up Key (
3
) or
Down Key (
4
) to show the saved images. Press Mode Key (
2
) again to return to the
measurement screen.
4.
Color palettes
Press Color Palette Key (
6
) to select the color palette (4 selectable color palettes) to view thermal images.
Ironbow
Rainbow
High contrast
Grayscale
5.
C/°F/K
Press Unit Key (
5
) for C
°F or K transferred.
6.
Power off
Press Mode Key (
2
) for more than 5 sec. to power off the unit. Auto power off time is around 30 sec..
FUNCTIONS
Press Mode Key (
2
) for scrolling more display functions, then press Up key (
3
) or Down key (
4
) to change the
functions, then press Trigger (
10
) to confirm it.
Emissivity
The default emissivity is 0.95, or select other default emissivity: Matt:0.95, Semi-matt:0.8, Semi-glossy:0.6,
Glossy:0.3
Select Set value to adjust the emissivity (0.1 to 1 step .01).
HAL
You can select Set Min temp or Set Max item to adjust the High Alarm (HAL) or Lo Alarm (LAL) limits
(step .1).
LAL
Language
Selectable Chinese or English.
Backlight
Selectable 5 levels of brightness.
Set Time
Set the date and time in MM/DD/YYYY (month/day/year) and HH/MM/SS (hour/minute/second) formats.
Time stamp
Turn on Time stamp to save thermal images with real-time stamp.
Turn off Time stamp to hide date and time on stored thermal images.
Erase Image
Select Yes, All image! to clear all stored thermal images.
Reset
Select Reset to recover the factory setting data.
Set parameter
Select Use Median Value
to reduce noise in an image.
Select No Filter
to display real image noise.
STORAGE & CLEANING
It should be stored at room temperature. The sensor lens is the most delicate part of the thermometer. The lens should be kept
clean at all times, care should be taken when cleaning the lens using only a soft cloth or cotton swab with water or medical alcohol.
Allowing the lens to fully dry before using the thermometer. Do not submerge any part of the thermometer.
BATTERIES
The thermometer incorporates visual low battery indication as follows:
‘Battery OK’: measurements
are possible
‘Battery Low’: battery needs to be
replaced, measurements are still possible
‘Battery Exhausted’: measurements are
not possible
When the ‘Low Battery’ icon indicates the battery is low, the battery should be replaced immediately with AA, 1.5V batteries.
Please note: It is important to turn the instrument off before replacing the battery otherwise the thermometer may malfunction.
Dispose of used battery promptly and keep away from children.
SPECIFICATION
Thermal Image Resolution
32*31
Measurement Range
-20~250°C (-4~482°F)
Accuracy (Tamb=20~26°C)
2% of reading, or 2°C(4°F) whichever is greater
Thermal Sensitivity
0.1°C
Frame Rate
9Hz
Field of View
40*40 deg
Emissivity Range
0.95 default – adjustable 0.1 to 1 step .01
Focus
Focus free
LCD (inch)
2.8
LCD Type
Color
Image Storage
Stores up to 60000 images/GB,
Bitmap (BMP) file format.
Memory Type
Support 8G micro SD card
Sensor Filter (um)
8~14um
Interface
USB
Battery Type
AA*4
Battery Life (hr)(backlit)
6
Dimensions
94.65 x 74.03 x 233.68mm (3.73 x 2.91 x 9.20 inch)
Weight
411 grams(14.5 oz) including batteries (AA*4pcs)
EMC/RFI: Readings may be affected if the unit is operated within radio frequency electromagnetic field strength of approximately 3 volts per
meter, but the performance of the instrument will not be permanently affected.
* IP54 Splash Proof
O
O
p
p
e
e
r
r
a
a
t
t
i
i
n
n
g
g
M
M
a
a
n
n
u
u
a
a
l
l
f
f
o
o
r
r
T
T
I
I
M
M
0
0
3
3
T
T
h
h
e
e
r
r
m
m
a
a
l
l
I
I
m
m
a
a
g
g
e
e
r
r
C
C
a
a
m
m
e
e
r
r
a
a
The thermal imager camera can measure from -20~250°C (-4~482°F) and displays the thermal image and temperature.
Furthermore, thermal images can be saved to a micro SD card. Transferring images to the software is included for image report
generation from these saved images.
OPERATION
1.
Power on
Press Mode Key (
2
) or Trigger (
10
) to power on the unit.
2.
Taking a thermal image and temperature
After power on, simply aim the thermal imager camera at the measure target with Lens
(
9
) and get the thermal image and temperature immediately. Please make sure the
target area is within the field of view.
Note: There are three cursors on the screen. The cross sign shows the temperature of
the object located in the middle of the screen. Other two moving cursors indicate the
highest and lowest temperatures in the thermal image.
3.
Save thermal images
Press Trigger (
10
) to save the thermal image to the micro SD card, press Up Key (
3
) or
Down Key (
4
) to show the saved images. Press Mode Key (
2
) again to return to the
measurement screen.
4.
Color palettes
Press Color Palette Key (
6
) to select the color palette (4 selectable color palettes) to view thermal images.
Ironbow
Rainbow
High contrast
Grayscale
5.
C/°F/K
Press Unit Key (
5
) for C
°F or K transferred.
6.
Power off
Press Mode Key (
2
) for more than 5 sec. to power off the unit. Auto power off time is around 30 sec..
FUNCTIONS
Press Mode Key (
2
) for scrolling more display functions, then press Up key (
3
) or Down key (
4
) to change the
functions, then press Trigger (
10
) to confirm it.
Emissivity
The default emissivity is 0.95, or select other default emissivity: Matt:0.95, Semi-matt:0.8, Semi-glossy:0.6,
Glossy:0.3
Select Set value to adjust the emissivity (0.1 to 1 step .01).
HAL
You can select Set Min temp or Set Max item to adjust the High Alarm (HAL) or Lo Alarm (LAL) limits
(step .1).
LAL
Language
Selectable Chinese or English.
Backlight
Selectable 5 levels of brightness.
Set Time
Set the date and time in MM/DD/YYYY (month/day/year) and HH/MM/SS (hour/minute/second) formats.
Time stamp
Turn on Time stamp to save thermal images with real-time stamp.
Turn off Time stamp to hide date and time on stored thermal images.
Erase Image
Select Yes, All image! to clear all stored thermal images.
Reset
Select Reset to recover the factory setting data.
Set parameter
Select Use Median Value
to reduce noise in an image.
Select No Filter
to display real image noise.
STORAGE & CLEANING
It should be stored at room temperature. The sensor lens is the most delicate part of the thermometer. The lens should be kept
clean at all times, care should be taken when cleaning the lens using only a soft cloth or cotton swab with water or medical alcohol.
Allowing the lens to fully dry before using the thermometer. Do not submerge any part of the thermometer.
BATTERIES
The thermometer incorporates visual low battery indication as follows:
‘Battery OK’: measurements
are possible
‘Battery Low’: battery needs to be
replaced, measurements are still possible
‘Battery Exhausted’: measurements are
not possible
When the ‘Low Battery’ icon indicates the battery is low, the battery should be replaced immediately with AA, 1.5V batteries.
Please note: It is important to turn the instrument off before replacing the battery otherwise the thermometer may malfunction.
Dispose of used battery promptly and keep away from children.
SPECIFICATION
Thermal Image Resolution
32*31
Measurement Range
-20~250°C (-4~482°F)
Accuracy (Tamb=20~26°C)
2% of reading, or 2°C(4°F) whichever is greater
Thermal Sensitivity
0.1°C
Frame Rate
9Hz
Field of View
40*40 deg
Emissivity Range
0.95 default – adjustable 0.1 to 1 step .01
Focus
Focus free
LCD (inch)
2.8
LCD Type
Color
Image Storage
Stores up to 60000 images/GB,
Bitmap (BMP) file format.
Memory Type
Support 8G micro SD card
Sensor Filter (um)
8~14um
Interface
USB
Battery Type
AA*4
Battery Life (hr)(backlit)
6
Dimensions
94.65 x 74.03 x 233.68mm (3.73 x 2.91 x 9.20 inch)
Weight
411 grams(14.5 oz) including batteries (AA*4pcs)
EMC/RFI: Readings may be affected if the unit is operated within radio frequency electromagnetic field strength of approximately 3 volts per
meter, but the performance of the instrument will not be permanently affected.
* IP54 Splash Proof
“Battery OK”:
Measurements are
possible
“Battery Low”:
Battery needs to be replaced,
measurements are still possible
“Battery Exhausted:
Measurements are not
possible
• When the ‘Low Battery’ icon indicates the battery is low, the battery should be recharged
by a USB port.
• Dispose of used batteries properly and keep away from children.
• If the device is not to be used for a long time, turn the power off, remove and store the
batteries in a cool, dry place.
•
Please Note:
It is important to turn the instrument off before replacing the battery
otherwise the thermometer may malfunction
SPECIFICATIONS:
Thermal Image Resolution:
32 x 32
Visual Image Resolution:
640 x 480
Measurement Range:
-20 to 350°C (-4 to 662°F)
Accuracy(Tamb=20~26°C): ±2% of reading, or 2°C (4°F) whichever is greater
Thermal Sensitivity:
0.1°C (0.1˚F)
Frame Rate:
9 Hz
Field of View:
33 x 33 deg
Emissivity Range:
0.95 default - adjustable 0.1 to 1 (in 0.01 steps)
Focus:
Focus free
LCD (inch):
2.8
LCD type:
Color
Memory Type:
Support micro SD card up to 32 gb (16 gb micro SD card
provided)
Spectral Range:
8 - 14 um
Interface:
USB
Battery Type:
3.7 V Li-ion rechargeable battery
Battery Life (with backlight): 3 hrs continuous use
Dimensions:
96.29 x 74.03 x 233.68 mm (3.79 x 2.91 x 9.20 inch)
Weight:
345 grams (12.7 oz) Including batteries
EMC/CRFI:
Reading may be affected if the unit is operated within radio frequency elec-
tromagnetic field strength of approximately 3 volts per meter, but the performance of the
instrument will not be permanently affected.
