If a wind radio sensor measures that the wind speed is above the threshold set on the sensor, the wind sensor sends the message of "wind alarm": the modules
tuned to it makes an upward manoeuvre and commands are inhibited as long as it remains the dangerous situation.
As soon as in the module is stored a wind sensor is automatically activated control of communication between the wind sensor and the module. If communication
is lost for more than 60 minutes, the module performs an upward movement for the protection of the roller. This manoeuvre is performed automatically every 60
minutes until the restoration of radio communication. The factory recommends keeping the "radio test" in order to identify in good time any malfunction of the radio
sensor. With the following procedure you can enable or disable the "test radio":
05. OPERATING LOGIC OF WIND SENSOR
05.1 TEST RADIO FUNCTION
10.1 UTILIZZANDO IL TRASMETTITORE (solo Atom e Leg)
ARCO
FLUTE, KUADRO, KORT
VISIO
Other transmitters...
01. Bring the motor in an intermediate position
02. Press MENU for about 5 sec, until «rS»
appears on display
03. Press 1 time PREV / 7 times NEXT.
«17» appears on display
04. Press STOP. The motor signals:
1 up = active, 1 down = inactive
05. To deactivate: press PREV
To activate: press NEXT
06. Press STOP. The motor signals:
1 up = active, 1 down = inactive
01. Bring the motor in an intermediate position
02. Holding down STOP, press PROG for
about 1 sec, until LEDs light
03. Press 1 time UP / 7 times DOWN.
04. Press STOP. The motor signals:
1 up = active, 1 down = inactive
05. To deactivate: press DOWN
To activate: press UP
06. Press STOP. The motor signals:
1 up = active, 1 down = inactive
01. Bring the motor in an intermediate position
02. Press MENU, «Menu rx» appears on
display
03. Press 1 time PREV / 7 times NEXT.
«17» appears on display
04. Press STOP. The motor signals:
1 up = active, 1 down = inactive
05. To deactivate: press DOWN
To activate: press UP
06. Press STOP. The motor signals:
1 up = active, 1 down = inactive
See the User manual of
the transmitter at
section:
«RECEIVER MENU -
Function 17 -
Test radio»
If the sun sensor measures a brightness above the threshold set for at least 2.5 minutes, sends the message "sun" and modules, tuned to it, command a
downward movement. If the sun sensor measures a brightness below the threshold set for at least 18 minutes, sends the message of "no sun" and modules MIR
CC, tuned to it, command an upward movement.
The "sun function" can be activated / deactivated from the transmitter (see transmitter manual under "sun function"). If the "sun function" is deactive, MIR CC
ignores the commands about the sun sent from the radio sensor.
06. OPERATING LOGIC OF SUN SENSOR
If the rain sensor measures a rain intensity exceeds the threshold set on the sensor, the rain sensor sends the message "rain" and modules MIR CC, tuned to it,
performs an upward or downward manoeuvre, according to how is set the rain sensor. The manual controls are still active. More rain sensors can be stored in the
same MIR CC.
07. OPERATING LOGIC OF RAIN SENSOR
09. TILTING FUNCTION
This feature can be useful, for example in the handling of sun protection. If
the function is activated, the
and
function of the transmitters
will command short movements which will allow easy orientation of the sun
protection. The command can also be given by any buttons connected to
the module; to use the function, press a button (less than 0.5 sec), then
press it again and hold it until you reach the desired orientation. The
factory sets the function to inactive.
RIGHT
LEFT
To set the function:
ARCO
ARCO
FLUTE, KUADRO, KORT
FLUTE, KUADRO, KORT
VISIO
VISIO
Other transmitters...
Other transmitters...
01. Bring the motor in an intermediate position
02. Press MENU for about 5 sec, until «rS»
appears on display
03. Press 1 time PREV / 2 times NEXT.
«12» appears on display
04. Press STOP. The motor signals the current
value (1 to 5 movements)
05. Press NEXT the number of times equal to
the desired setting (1 to 5)
06. Press STOP. The motor signals the new
value (1 to 5 movements)
01. Bring the motor in an intermediate position
02. Press MENU for about 5 sec, until «rS»
appears on display
03. Press 8 times NEXT.
«08» appears on display
04. Press STOP. The motor signals the current
value (1 to 7 movements)
05. Press NEXT the number of times equal to
the desired setting (1 to 7)
06. Press STOP. The motor signals the new
value (1 to 7 movements)
01. Bring the motor in an intermediate position
02. Holding down STOP, press PROG for about
1 sec, until LEDs light
03. Press 1 time UP / 2 times DOWN.
04. Press STOP. The motor signals the current
value (1 to 5 movements)
05. Press DOWN the number of times equal to
the desired setting (1 to 5)
06. Press STOP. The motor signals the new
value (1 to 5 movements)
01. Bring the motor in an intermediate position
02. Holding down STOP, press PROG for about
1 sec, until LEDs light
03. Press 8 times DOWN.
04. Press STOP. The motor signals the current
value (1 to 7 movements)
05. Press DOWN the number of times equal to
the desired setting (1 to 7)
06. Press STOP. The motor signals the newt
value (1 to 7 movements)
01. Bring the motor in an intermediate position
02. Press MENU, «Menu rx» appears on
display
03. Press 1 time PREV / 2 times NEXT.
«12» appears on display
04. Press STOP. The motor signals the current
value (1 to 5 movements)
05. Press UP the number of times equal to the
desired setting (1 to 5)
06. Press STOP. The motor signals the new
value (1 to 5 movements)
01. Bring the motor in an intermediate position
02. Press MENU, «Menu rx» appears on
display
03. Press 8 times NEXT.
«08» appears on display
04. Press STOP. The motor signals the current
value (1 to 7 movements)
05. Press UP the number of times equal to the
desired setting (1 to 7)
06. Press STOP. The motor signals the new
value (1 to 7 movements)
See the User manual of
the transmitter at
section:
«RECEIVER MENU -
Function 12 -
Orientation»
See the User manual of
the transmitter at
section:
«RECEIVER MENU -
Function 08»
ü
If you try to set «Orientation time» greater than level 5, the value is rejected and the motor makes 2 short movements down.
ü
When «Orientation time» is set on level 1 (inactive), if you command the orientation movements by transmitter or by command buttons, the motor will not
move.
ü
If you try to set «AIR Change» greater than level 7, the value is rejected and the motor makes 2 short movements down.
ü
When «AIR Change» is set on level 1 (inactive), if you command the orientation movements by transmitter or by command buttons, the motor will not
move.
N° of movements
Duration of movement
1
inactive
2
050 msec
3
100 msec
4
150 msec
5
200 msec
This feature is especially useful if you want to identify a favorite position of the
roller blind. Recalling the intermediate limit switch function by a stored portable
transmitter, a complete operation of descent is carried out and elapsed the
work time, a short upward movement is carried out whose duration can be set
via this parameter.
08. “AIR CHANGE“ FUNCTION
N° of movements
AIR CHANGE
1
inactive
2
02 sec
3
03 sec
4
04 sec
5
05 sec
6
06 sec