background image

                                                                     

12

 
10.        Special service situations: 
 

If moisture or liquid is observed around or under a Master-Bilt cabinet, an immediate investigation 
should be made by qualified personnel to determine the source of moisture or liquid.  The investigation 
made should determine if the cabinet is malfunctioning or if there is a simple housekeeping problem. 
 
Moisture or liquid around or under a cabinet is a potential slip/fall hazard for persons walking by or 
working in the general area of the cabinet. 
 
Any cabinet malfunction or housekeeping problem that creates a slip/fall hazard around or under a 
cabinet should be corrected immediately.  

 
MASTER-BILT PART NUMBERS 

 
The table below gives Master-Bilt part numbers.  Use this chart when ordering replacement parts for your 

GT

 

cases. 

Description 

GT-50 

GT-60 

GT-80 

Aluminum Extrusions: 
Bumper 
Upper Hand Rail 
Lid Handle 
Trim, L.H. and Front 
Trim, R.H. and Front 

       

49-01127 
49-01122 
49-01118 
49-01138 
49-01139 

 

49-01128 
49-01123 
49-01119 
49-01138 
49-01139 

 

49-01129 
49-01124 
49-01120 
49-01138 
49-01139 

Coil Defrost Heater 

17-00488 

17-00491 

17-00492 

Compressor 

03-14902 03-14902 03-14902 

Condenser Coil 

07-13296 

07-13296 

07-13296 

Condenser Fan Blade 

15-13093 

15-13093 

15-13093 

Condenser Fan Motor 

13-00311 

13-00311 

13-00311 

Condenser Fan Motor Bracket 

13-00754 

13-00754 

13-00754 

Crankcase Pressure Valve 

 

 

 

Defrost Heater Clip 

17-09128 

17-09128 

17-09128 

Defrost Termination Control 

19-01163 

19-01163 

19-01163 

Drain Trough Heater 

17-00448 

17-00449 

17-00451 

Drier 

09-09171 

09-09171 

09-09171 

Evaporator 

Coil 

07-01018 07-01019 07-01017 

Capillary tub 

11-01450 

11-01450 

11-01450 

Fluorescent Lamp, 24” 

 

23-01576 

 

Fluorescent Lamp, 36” 

23-01577 

23-01577 

23-01577 

Front Glass Heater 

17-00394 

17-00392 

17-09039 

Front Glass Seal 

31-00859 

31-00859 

31-00859 

Glass 

31-01171 31-01172 31-01174 

Glass Lid 

31-00853 

31-00851 

31-00850 

Heater Safety Control 

19-01164 

19-01164 

19-01164 

Lamp Ballast 

23-01693 

23-01693 

23-01693 

Lid Center Track 

49-01131 

49-01131 

49-01131 

Light Shield Heater 

17-00397 

17-00386 

17-00385 

Mullion 

Heater 

17-00389 17-00387 17-00388 

Plastic Trim, RH Side Panel 

29-00600 

29-00600 

29-00600 

Plastic Trim, LH Side Panel 

29-00601 

29-00601 

29-00601 

Power Cord 

21-00312 

21-00312 

21-00312 

Price Tag Extrusion, 10’ 

49-01434 

49-01434 

49-01434 

Side Panel Heater, RH 

17-00408 

17-00408 

17-00408 

Side Panel Heater, LH 

17-00409 

17-00409 

17-00409 

Lamp Socket, Spring 

23-01698 

23-01698 

23-01698 

Lamp Socket, Fixed 

23-01699 

23-01699 

23-01699 

Temperature Control 

19-13765 

19-13765 

19-13765 

Summary of Contents for J - Version GT-50 s
















Reviews: