background image

 

 

6

NOTICE 

 

Read this manual before installing, cleaning, or performing any maintenance on your cabinet.  Keep the 
manual and refer to it before doing any service on the equipment.  Failure to do so could result in personal 
injury or damage to the cabinet. 

 

 

DANGER

 

Improper or faulty hook-up of electrical components on the refrigeration units can result in 

severe injury or death.  All electrical wiring hook-ups must be done in accordance with all applicable local, 
regional or national standards.

 

 

 

NOTICE

 

Installation and service of the refrigeration and electrical components of the cabinet must 

be performed by a refrigeration mechanic and/or a licensed electrician. 

 
 
The portions of this manual covering refrigeration and electrical components contain technical instructions intended 
only for persons qualified to perform refrigeration and electrical work.  This manual cannot cover every installation, use 
or service situation. If you need additional information, call or write us: 
 
 
Customer Service Department 

Master-Bilt Products 

Highway 15 North 
New Albany, MS  38652 
Phone (800) 684-8988 
Fax (866) 882-7629 
 

 
 
GENERAL INSTRUCTIONS 

 
1.  Be sure the ice merchandiser is properly installed by competent service people. 
 
2.  Keep the ice merchandiser clean and sanitary so it will meet your local sanitation codes. Clean the unit with a mild 
detergent and water, then rinse. 
 
3.  Rotate your stock so that older stock does not accumulate.   
 
4.  Do not place product in the ice merchandiser when it is soft or partially thawed. Also, product should not be put in 
the ice merchandiser for at least 6 hours after it is started. 
 
5.  Stock ice merchandiser as quickly as possible, exposing only small quantities to condition temperatures for short 
periods of time. 

 

 

 

 

   

 

 
NOTICE TO STORE OWNERS / MANAGERS 

 

Moisture or liquid around or under the cabinet is a potential slip/fall hazard for persons walking by or working 
in the general area of the cabinet.  Any cabinet malfunction or housekeeping problem that creates a slip/fall 
hazard around or under the cabinet should be corrected immediately.

 

 
If moisture or liquid is observed around or under a 

Master-Bilt

 Ice Merchandiser, an immediate investigation should be 

made by qualified personnel to determine the source of the moisture or liquid.  The investigation should determine if the 
ice merchandiser is malfunctioning or if there is a drainpipe leaking. 

 

 

Summary of Contents for IM-23-HGP

















Reviews: