Massoth DiMAX Manual Download Page 19

Page: 19 / 24

5. Technische Daten

Spannung:

• automatische Versorgung durch das

DiMAX-Buskabel oder LGB

-Buskabel

• Im Funkbetrieb : 10 .. 24V DC/DCC

oder 12 .. 18V AC an ‚Power‘

Anschluss

• DCC-Programmierspannung an

‚Power‘ Anschluss : 12 .. 24V 0-24 V

Stromaufnahme:

• ca. 30mA (ca. 50mA im Funkbetrieb).

• 100..250mA Antwortstrom zur

Programmierbestätigung.

Temperaturbereich: -20 - +45°C

Abmessungen: 80 x 70 x 20 mm

(L x B x H)

Hinweis zur Temperatur: Um Kondens-

wasserbildung zu vermeiden benutzen

Sie die Elektronik bei Temperaturen

unter 0°C nur, wenn diese vorher aus

einem beheizten Raum kommt. Die

Eigenwärme des Fahrbetriebs reicht

aus um Kondenswasserbildung zu

verhindern.

5. Technical Specifications

Power Supply:

• Automatic power supply by the DiMAX

bus cable or LGB

bus cable

• During wireless operation: 10…24 Volt

DC / DCC or 12…18 Volt AC at power

terminal

• DCC programming power at power

terminal 12…24 Volt

Current:

• About 30 mAmp (about 50 mAmp in

wireless operation)

• 100…250 mAmp during programming

30-2000 mAmps

Temperature Range: -4°F to +113°F

Measurements: 80 x 70 x 20 mm

(L x W x H)

Note: If you intend to utilize this decoder

below freezing temperatures, make sure

it was stored before in a heated environ-

ment before operation to prevent the

generation of condensed water. The heat

generated during operation is sufficient

to prevent condensed water.

Summary of Contents for DiMAX

























Search results

Summary of Contents for DiMAX

Reviews:

Brands by name

Popular brands

Massoth DiMAX, Manual

Search results

Summary of Contents for DiMAX

Reviews:

Brands by name

Popular brands