MASSO G2 Documentation Download Page 20

Page: 20 / 477

MASSO

MASSO Documentation

The front part of the enclosure is made of ABS plastic.

The rear mounting plate is made of anodized aluminum.

The touch glass is made of toughened capacitive touch glass.

What is the enclosures IP (Ingress Protection) rating?

The unit does not have or require cooling fans which means that there is no internal positive or

negative pressure to pull dust particles. The front part assembly with the rear panel has a lip to

prevent dust or water from going into the system but direct dust or liquids should be avoided.

The rear panel also has mounting holes and a cutout for wiring, the user should make sure to cover

or close these during installation.

Will the normal MASSO-G3 and MASSO Touch software be different or will

have different features?

Both the models will have exact same software features and user interface.

MASSO Touch was developed as per client and OEM requests to have an integrated design and

also to solve issues with 3rd party touch screen not working.

Both the models will have software updates released at the same time with same features added.

Can the two red and green buttons on the unit only be used for cycle start and

stop?

The buttons are wired to normal inputs and can be assigned any function from the F1-Setup screen.

What's the weight of the unit?

The MASSO Touch weighs about 4.5kg (9.92lb).

Mechanical dimensions and mounting information?

Please use this link

CLICK HERE

v5.18 - 08 Apr,2021

www.masso.com.au

Page 20 of 477

Summary of Contents for G2






























































































































































































































































































































































































































































































Search results

Summary of Contents for G2

Reviews:

MASSO G2, Documentation, Page: 20 / 477

Search results

Summary of Contents for G2

Reviews: