manualshive.com logo in svg

Masoneilan SVI II ESD, Installation And Maintenance Manual

Share
Download
Masoneilan SVI II ESD Installation And Maintenance Manual Download Page 217

© 2017 Baker Hughes, a GE company, LLC. All rights reserved.

Masoneilan SVI II ESD Installation and Maintenance Manual 

=

|

 

217

Appendix I. Determining an SVI Positioner 
Compliance Voltage in a Control System

This discussion explains how to determine compliance voltage for an SVI positioner. It applies to 
the SVI II AP, SVI II ESD, SVI II APN and SVi1000.

A definition of compliance voltage is: The voltage that must be available at the control system 
output in order to drive the control current through the SVI II AP and all the resistive devices in 
series with it.

Measuring the voltage across the SVI II AP terminals doesn't give the true available system 
compliance voltage as the positioner self-regulates voltage as current flows through it. 
Additionally, it also doesn't confirm what system voltage is available under load conditions. 

Therefore, if compliance testing needs to be done, it is best done before installation.

Use a 1K potentiometer as this is the maximum for most analog output cards and as at 20 mA 
this equals 20 VDC, which is a sufficient maximum.

Compliance Test Setup

1. Configure a test setup as in Figure 94.

Figure 94 Compliance Voltage Test Setup

Summary of Contents for SVI II ESD





























































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands