background image

This device complies with Part 15.236 of the FCC Rules. Operation is subject to the following 

two conditions:(1)This device may not cause harmful interference and (2) This device must

accept any

The changes or modifications not expressly approved by the party responsible for

compliance could void the user’s authority to operate the equipment.

IMPORTANT NOTE: To comply with the FCC RF exposure compliance requirements, no

change to the antenna or the device is permitted.

could result in the device exceeding the

to operate the device.

Thank you for purchasing our product. This PLL synthesized wireless microphone system

operates in UHF band frequency with 8 selectable channels. Please read this instruction

manual carefully before operating the system. This manual covers the function and operation

of the wireless microphone system.

 Safety

Do not spill liquid on the appliance and do not drop it on a hard concrete floor.
Do not place the equipment near heat sources such as radiators, heating ducts, amplifier, etc.
Do not expose the equipment to direct sunlight, extremely dust, excessive moisture, rain,

mechanical vibrations, or shock. 
Take out the battery from transmitter, if the appliance has been not used for a longer period.

This will avoid the damage resulting from a defective leaking battery. 

WARNING: To reduce the risk of fire or electric shock, do not use the products near water

and do not expose them to rain or moisture. 

Environment

When disposing the equipment, remove the batteries, separate the case, circuit boards,

and cables, and dispose of all components in accordance with local waste disposal rules.

Do not throw used batteries into a fire or garbage bin with domestic rubbish.   Be sure to

dispose of used batteries in accordance with local waste disposal rules.

If the equipment is not going to be used for a long time, disconnect the AC adapter from

the power outlet. Please note that if you turn the equipment off while leaving the AC

adapter plugged in, it is not fully isolated from the power supply.

No guarantee claims for the equipment and no liability for any resulting personal damage

or material damage will be accepted if the equipment is used for other purpose than

originally intended, if the equipment is not correctly connected or operated, or if the

equipment is not repaired in an expert way.

Notice :

FCC Statement

interference received, including interference that may cause undesired operation.

Introduction

Any change to the antenna or the device

RF exposure requirements and void user’s authority

1

Summary of Contents for RS-21B

















Reviews: