background image

 

 

8

To Stop 

Normal shutdown 

1.  With the throttle lever closed from ON to OFF, run the engine for 3-5 minutes at low speed, and 

after temperature is lowered, turn the switch to the 

OFF

 position. 

2.  Close the fuel shut-off valve by moving the fuel cock lever to the CLOSED position. 

Emergency shutdown 

Move the throttle lever quickly to the IDLE position, and turn the engine ON/OFF switch to the OFF 

position.   

 

Maintenance and Storage: 

Periodic Maintenance Schedule 

 

 

 

Daily 

Before 

Starting 

After 

First 

5   

hours 

Every 

Week   

or 

25 hours 

Every   

month   

or 

100 hours 

Every   

3 months 

or   

300 hours 

Check fuel level. 

 

 

 

 

 

Check oil level of machine. 

 

 

 

 

 

Check  fuel  line  and  fittings  for  cracks  or 

leaks. 

 

 

 

 

 

Tighten ramming shoe hardware. 

 

 

 

 

 

Check and tighten engine cylinder screws. 

 

 

 

 

 

Check and tighten external hardware. 

 

 

 

 

 

Clean engine cooling fins. 

 

 

 

 

 

Clean and check spark plug gap. 

 

 

 

 

 

Replace spark plug. 

 

 

 

 

 

Clean recoil starter. 

 

 

 

 

 

Change ramming system oil. * 

 

 

 

 

 

Clean engine muffler and exhaust port. 

 

 

 

 

 

* Change ramming system oil after first 50 hours of operation. 

Note: If engine performance is poor, check, clean, and replace air filter elements as needed. 

 

Air Cleaner Cleaning for EMR70H (6 to 12 months Service): 

Remove element from pre-cleaner at the top of crank case and clean it with cleaning oil (kerosene). 

Take  of 

Bolt,  Cover

  of  the  crankcase  upper  part  and  take 

Element

  off 

AIR  CLEANER

. Wet  the 

bottom element (gray) with 7-9cc and let upper element (yellow) be familiar with oil. 

 

 

 

 

 

Summary of Contents for EMR70H















Reviews: