background image

when the ice supply is low or full and starts or stops the ice 
making process accordingly.

power to the unit.

New Sounds

your household refrigerator. Because these sounds are 
new to you they may be of a concern but are most likely 
normal. The ice production process will make noises that 

valves opening and closing. Following are some of the 

A buzzing sound will be heard when the water valve 

water line.

evaporator plate and into the water reservoir. 

A "thud" when the ice slab is released from the 
evaporator plate and slides onto the grid cutter.

"Clicks" when the cubes fall into the ice storage bin.

machine.

An air noise from the condenser fan.

Ice Production

In normal mode the ice machine will produce  up to 39 
pounds (17.7 kg) of clear ice in a 24-hour period when 
installed in a 72°F ambient with a 55°F water supply. In 
"ECO" mode (see page 16) the ice machine will produce up 
to 29 pounds (13.2 kg) of clear ice in the 24 hour period.

24-hours of operation the unit will produce up to 39 lbs of

the ice storage bin is maintained at a temperature slightly

production rate will overcome the ice melt and the storage

NOTE

NOTE

The ice machine will keep producing ice until the ice 
machine’s bin is full and will restart automatically when 
ice needs to be replenished in the bin. The ice bin is 

machine to run for 24-48 hours to accumulate ice in the ice 
machine’s bin.

ICE MAKER OPERATION

2

3

New Sounds

your household refrigerator. Because these sounds are 
new to you they may be of a concern but are most likely 
normal. The ice production process will make noises that 

"Initial" ice production and ice accumulated in the storage 

bin will vary significantly. This is normal. During the first 

24 hours of operation, the unit will produce up to 39 lbs of 

ice at the above ambient and water temperature 

conditions, but when starting with an empty ice storage 

bin, the storage bin may accumulate up to 23 lbs of ice. 

By design, the ice storage bin is maintained at a 

temperature slightly above freezing to allow the stored 

ice to to slowly melt to preserve the ice quality and clarity 

and assure a constant supply of fresh ice. As ice is 

accumulated in the bin, the ice production rate will 

overcome the ice melt and the storage bin will fill to 

capacity.

15

Summary of Contents for MLCL215





































Reviews: