Marvel ML24FA Installation, Operation And Maintenance Instructions Download Page 3

3

NOTE

!

CAUTION

XXXXXXXXXXXX

XXXXXXXXXXXX

UNPACKING YOUR APPLIANCE

!

WARNING

WARNING - Help Prevent Tragedies

Child entrapment and suffocation are not problems of 

the past. Junked or abandoned refrigerators are still 

dangerous - even if they sit out for "just a few hours".

If you are getting rid of your old refrigerator, please 

follow the instructions below to help prevent acci-

dents.

Before you throw away your old refrigerator or 

freezer:

•  Take off the doors or remove the drawers.

•  Leave the shelves in place so children may not 

easily climb inside.

!

WARNING

WARNING - 

Dispose of the plastic bags which can 

be a suffocation hazard.

Warranty Registration

It is important you send in your warranty registration card 

immediately after taking delivery of your appliance or you 

can register online at www.agamarvel.com.

The following information will 

be required when registering 

your appliance.

Service Number

Serial Number

Date of Purchase

Dealer’s name and address

The service number and serial number can be found on the 

serial plate which is located inside the cabinet on the left 

side near the top. (See figure 1).

!

WARNING

EXCESSIVE WEIGHT HAZARD

Use two or more people to move product.

Failure to do so can result in personal injury.

Remove Interior Packaging

Your appliance has been packed for shipment with all parts 

that could be damaged by movement securely fastened.  

Remove internal packing materials and any tape holding in-

ternal components in place. The owners manual is shipped 

inside the product in a plastic bag along with the warranty 

registration card, and other accessory items. 

Important

Keep your carton and packaging until your appliance has 

been thoroughly inspected and found to be in good condi-

tion. If there is damage, the packaging will be needed as 

proof of damage in transit. Afterwards please dispose of all 

items responsibly. 

Note to Customer

This merchandise was carefully packed and thoroughly 

inspected before leaving our plant. Responsibility for its 

safe delivery was assumed by the retailer upon acceptance 

of the shipment. Claims for loss or damage sustained in 

transit must be made to the retailer.

DO NOT RETURN DAMAGED MERCHANDISE TO THE 

MANUFACTURER - FILE THE CLAIM WITH THE 

RETAILER.

If the appliance was shipped, handled, or stored in other 

than an upright position for any period of time, allow the ap-

pliance to sit upright for a period of at least 24 hours before 

plugging in. This will assure oil returns to the compressor. 

Plugging the appliance in immediately may cause damage 

to internal parts.

Figure 1

Online registration 

available at 

www.agamarvel.com

Summary of Contents for ML24FA

























Reviews: