background image

— 18 —

STORAGE

For long-term storage of the mister, first perform all regular maintenance procedures and needed
repairs. Empty the fuel tank. Disconnect the fuel supply line from the carburetor and depress the
primer bulb until fuel stops discharging from the fuel-return line.
Start the engine and allow it to run until it stops. Pull the starter cord a few times to remove any excess
fuel from the engine. Remove the spark plug and insert a small amount of oil into the cylinder. Slowly
pull the starter cord and bring the piston to a position closest to the spark plug hole. Re-install the
spark plug. Apply a thin coating of oil to all the metal surfaces and store the mister in a dry place.

TROUBLESHOOTING

If further assistance is required, contact your local authorized Maruyama service dealer.

Problem

Cause

Action

Engine Will Not Start

STOP switch set to off position

Move switch to on position 

Empty fuel tank

Fill fuel tank

Primer bulb wasn’t pushed enough

Press primer bulb until fuel flows 

through fuel return line 

Engine flooded

Use warm engine starting procedure

Engine Lacks Power or dropped  

Dirty air filter 

Clean or replace air filter

down when blowing.

Clogged spark arrester or exhaust port.

Clean spark arrester or exhaust port.

Blower pipes clogged, loose or damaged.

Unclog or tighten or replace

MAINTENANCE PERIOD

Every

Every

Every

Maintenance

Daily

20 hours

50 hours 100 hours

Check and replenish fuel

Check for fuel leakage

Check bolts, nuts and screws for tightness or missing

Check engine idle speed adjustment

Clean air filter element

Remove dust and dirt from engine screen

Remove dust and dirt from air intake screen

Tighten bolts and nuts

Clean spark plug and adjust electrode gap

Remove dust and dirt from cylinder fins

Remove carbon deposits  in exhaust port

Clean spark arrester

Replace fuel filter

Remove carbon deposits on piston head and combustion chamber

Remove carbon deposits in transfer ports

Replace fuel tube, fuel tank cap gasket

It is recommended to replace every 3 years

: Service to be performed by an authorized Maruyama engine dealer.

: Service more frequently under dusty conditions.

NOTE:

The service intervals indicated are to be used as a guide.

Service to be performed more frequently as necessary depending on operating condition.

Use Maruyama standard 50:1 two-cycle engine oil.

Summary of Contents for Mister MM300





















Reviews: