AIR CONDITIONING SYSTEM 7B-31
Compressor Relay Inspection
1) Disconnect negative (–) cable from battery.
2) Remove compressor relay (1) from main fuse box.
3) Check that there is no continuity between terminal “c” and “d”. If
there is continuity, replace relay.
4) Connect battery positive (+ ) terminal to terminal “b” of relay
and battery negative (–) terminal to terminal “a” of relay, and
then check continuity between terminal “c” and “d”. If there is
no continuity, replace relay.
Compressor Drive Belt Inspection and Adjustment
Inspection
•
Check compressor drive belt (1) for wear, crack, deformation
and cleanliness. If any defect is found, replace the belt with
new one referring to “Compressor Drive Belt Re moval and
Installation: Manual Type”.
•
Check compressor drive belt tension by measuring how much
it deflects when pushed intermediate point between magnet
clutch pulley (6) and crankshaft pulley (3) with about 100 N (10
kg) force after rotating crankshaft pulley 360
0
. If belt tension is
out of specification, adjust belt tension referring to “Adjustment”.
Compressor drive belt tension
“a”: 5 – 7 mm (0.19 – 0.28 in.)
Adjustment
1) Loosen tension pulley bolt (4).
2) Adjust belt tension by tighten or loosen tension pulley adjusting
bolt (2).
3) Tighten tension pulley bolt.
4) Rotate the crankshaft pulley 360
0
, and then recheck belt tension.
Compressor Drive Belt Removal and Installation
Removal
1) Loosen tension pulley bolt (4).
2) Loosen belt tension loosening tension pulley adjusting bolt (2).
3) Remove compressor drive belt).
Installation
Reverse removal procedure noting the following instruction.
•
Adjust belt tension referring to “Compressor Drive Belt
Inspection and Adjustment: Manual Type”.
"d"
"b"
"a"
"c"
Summary of Contents for Zen Estilo 2018
