background image

9

S

PECIFICATIONS

*

Frequency Response . . . . . . . . . . . . . . . . . . . . .

Dispersion  . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Sensitivity. . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Impedance . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Crossover Frequency. . . . . . . . . . . . . . . . . . . . .

High Frequency Driver  . . . . . . . . . . . . . . . . . . .

Low Frequency Drivers . . . . . . . . . . . . . . . . . . .

Cabinet  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Components . . . . . . . . . . . . . . . . . . . . . . . . . . .

Recommended Amplifier Power. . . . . . . . . . . . .

Binding Post Inputs . . . . . . . . . . . . . . . . . . . . . .

Weight. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Dimensions (HxWxD)  . . . . . . . . . . . . . . . . . . . .

50–25,000 Hz ± 3 dB

80° x 30°

94 dB @ 2.83 volts/ meter

4 Ohms. Compatible with 4, 6 or 8 Ohm rated 
amplifiers.

900 & 2,200 Hz

1.2” x 2.4” (3.2cm x 6.1cm) Folded Motion 
Transducer with 4.5” x 2.75” (11.4cm x 7cm) 
diaphragm.

Two 6.5” (16.5cm) aluminum cone with cast poly-
mer basket. Non-resonant asymmetrical chamber 
format. Rigid structured dust cap to reduce cone 
break-up modes.

Ported

Custom air core coil and low DCR steel laminate 
inductors. Polypropylene film capacitors in series 
and low DF electrolytic capacitors in parallel. 
Tweeter thermal/current protection.

20–300 watts 

Custom 5-way tool-less binding posts

30.5 lbs. (13.8 kg)

7.6” x 22.8” x 12.8” 
(19.2cm x 58cm x 32.6cm)

Summary of Contents for Motion 50XT













Reviews: