THRILL Compact PAR 64 LED
Safety and Installation Guide
WARNING!
Read the safety precautions in
this guide before installing or using this
product.
Introduction
The THRILL Compact PAR 64 LED is a compact color-mixing
lighting fixture with 5 long-life six-color LED emitters. It provides
strobe effects, full-range dimming, and full 0-100% control of its
red, green, blue, white, amber, and UV light. The lightweight
construction and flexible control options make it ideal for mobile
DJs and small venues.
It is supplied with this guide, a user guide, power cables, a remote
control, and a multi-function bracket for attachment of a suitable
rigging clamp (not included), or use as a floor stand.
Before installing and using the fixture:
1.
Read the safety information.
2.
Unpack the fixture and ensure that there is no transportation
damage. Do not attempt to operate a damaged fixture.
3.
Ensure that your AC voltage and frequency match the power
requirements of the fixture.
4.
Check the Martin Professional website at www.martin.com
for the most recent product documentation and technical
information. Martin document revisions are identified by
the revision letter below the legal notices.
Safety information
The following symbols identify important safety information:
Warning!
Safety hazard.
Risk of severe
injury or death.
Warning!
Powerful light
emission. Risk
of eye injury.
Warning!
See user
manual for
important
safety
information.
Warning!
Hazardous
voltage. Risk
of lethal
electric shock.
Warning!
Hot surfaces.
Warning!
Fire hazard.
This lighting fixture presents risks of severe injury
or death due to fire hazards, electric shock and
falls. It is Exempt Group (RG 0) per EN 62471,
where no optical hazard is considered reasonably
foreseeable, even for continuous, unrestricted use.
Install, operate and service this product only as directed, or you
may create a safety hazard or cause damage that is not covered
by product warranties.
Follow the safety precautions below and observe all warnings on
the product. Follow the instructions and observe all
warnings in the product’s user guide. Keep this
information for future reference.
For the latest user documentation and other information about
this and all Martin products, visit the Martin website at
http://www.martin.com.
Respect all locally applicable laws, codes and regulations when
installing, operating or servicing the product.
Protection from electric shock
Do not expose the product to water or moisture.
Disconnect the product from AC power before
carrying out installation or maintenance and when
the product is not in use.
Ensure that the product is electrically connected to ground
(earth).
Use only a source of AC power that complies with local building
and electrical codes and has both overload and ground-fault
(earth-fault) protection.
Socket outlets or external power switches used to supply the
product with power must be located near the product and easily
accessible so that it can easily be disconnected from power.
Replace blown fuses with ones of the specified type and rating.
Isolate the product from power immediately if the power plug or
any seal, cover, cable, or other component is damaged,
defective, deformed, wet or showing signs of overheating. Do not
reapply power until the problem is corrected.
Before connecting the product to power, check that all power
distribution equipment and cables are undamaged and rated for
the electrical requirements of all connected products.
The maximum current through the MAINS OUT socket is of 3 A.
Do not use the MAINS OUT socket to connect power to more
than:
• Six (6) additional Compact PAR 64 LED fixtures at 100-120 V,
or
• Ten (10) additional Compact PAR 64 LED fixtures at
200-240 V.
Protection from burns and fire
Do not operate the fixture if the ambient
temperature (Ta) exceeds 40° C (104° F).
The surface of the product casing can reach up to
45° C (113° F) after 5 minutes of operation and
during a steady on state. Avoid contact by persons
and materials. Allow the fixture to cool for at least 10
minutes before handling.
Keep flammable materials well away from the fixture. Keep all
combustible materials (e.g. fabric, wood, paper) at least 100 mm
(4 in.) away from the fixture.
Ensure that there is free and unobstructed airflow around the
fixture. Provide a minimum clearance of 100 mm (4 in.) around
fans and air vents.
Do not illuminate surfaces within 200 mm (8 in.) of the fixture.
Do not attempt to bypass thermostatic switches or fuses.
Do not stick filters, masks or other materials onto any optical
component.
The fixture’s lenses can focus the sun’s rays inside the fixture,
creating a risk of fire and damage. Do not expose the front of the
fixture to sunlight or any other bright light source.
Protection from eye injury
Lighting fixtures emit possibly hazardous radiation.
Do not look at an operating lamp. Eye injury may
result.
To minimize the risk of eye injury or irritation, disconnect lighting
fixtures from power at all times when not in use, and provide well-
lit conditions to reduce the pupil diameter of anyone working on
or near them.
Do not look at output from lighting fixtures with magnifiers,
telescopes, binoculars or similar optical instruments that may
concentrate the light.
Ensure that persons are not looking directly into a lighting fixture
when it lights up suddenly. This can happen when power is
applied, when the fixture receives a remote control signal, or
when certain control menu items are selected.
Protection from injury
Do not attempt to repair a defective product or
modify the product in any way. LEDs are not user-
replaceable. Refer all service to your Martin dealer
or contact Martin directly for technical support
through www.martin.com/contact-support.
Fasten the fixture securely to a fixed surface or structure when in
use. The fixture is not portable when installed.
Ensure that any supporting structure and/or hardware used can
hold at least 10 times the weight of all the devices they support
and complies with locally applicable regulations.
To suspend the fixture from a rigging structure, use a suitable
rigging clamp. Do not use safety cables as the primary means of
support.
If the product is installed in a location where it may cause injury
or damage if it falls, install as directed a secondary attachment
such as a safety cable that will hold the machine if a primary
attachment fails. The secondary attachment must be approved
by an official body such as TÜV as a safety attachment for the
weight that it secures, must comply with EN 60598-2-17 Section
17.6.6 or BGV C1 / DGUV 17, and must be capable of bearing a
static suspended load at least six times the weight of the fixture
(or more if required by locally applicable regulations). Check that
all external covers and rigging hardware are securely fastened.
Block access below the work area and work from a stable
platform whenever installing, servicing or moving the fixture.
Do not operate the fixture with missing or damaged covers,
shields or any optical component.
In the event of an operating problem, stop using the fixture
immediately and disconnect it from power. Do not attempt to use
a fixture that is obviously damaged.
Do not modify the fixture in any way not described in this manual
or install other than genuine Martin parts.
Flashing light can trigger epileptic seizures in flicker-sensitive
persons. Provide notice when strobe lighting is in use at the
entrance(s) to the venue. Mount flashing lights as high above
head height as practicable and avoid extended periods of
continuous flashing, particularly at 10 to 20 flashes per second.
Stop lights from flashing immediately if a person has an epileptic
seizure.
The remote control supplied with this product contains a
coin/button/cell battery. If the coin/button/cell battery is swallowed
it can cause severe internal burns in just two hours and lead to
death. Keep new and used coin/button/cell batteries away from
children and animals. If the coin/button/cell battery compartment
does not close securely, stop using the product and keep away
from children and animals. If you think coin/button/cell batteries
have been swallowed or placed inside of the body seek
immediate medical attention.
Fixture overview
Physical installation
The THRILL Compact PAR 64 LED is
designed for indoor use only and must be
used in a dry location with adequate
ventilation.
Fasten the fixture to a secure structure or surface. Do not stand
it on a surface or leave it where it can be moved or fall over. If
you install the fixture in a location where it may cause injury or
damage if it falls, secure it as directed using a securely anchored
safety cable that will hold the fixture if the primary fastening
method fails.
Fastening the fixture to a flat surface
The fixture can be fastened to a hard, fixed, flat surface. Ensure
that the surface and all fasteners used can support at least 10
times the weight of all fixtures and equipment they support and
comply with locally applicable regulations.
Fasten the fixture securely. Do not stand it on a surface or leave
it where it can be moved or fall over. To use the bracket as a floor
stand:
1.
Loosen the hand wheels on both sides of the bracket.
2.
Unfold the bracket as required, taking caution not to over
extend the bracket.
3.
Position the fixture and adjust the tilt angle.
4.
Tighten both hand wheels. Do not over-tighten.
1
Multi-function bracket
7
AC Mains out
2
LED emitters
8
DMX In
3
Hand wheel
9
Secondary attachment point
4
IR receiver
10
Control panel
5
AC Mains in
11
DMX Out
6
Microphone
12
Clamp attachment point
1
2
4
7
3
5
6
9
11
12
10
8
