background image

14 

Installation and Setting Up 

 

 

Before connecting the machine to power, verify that the AC supply is adequately 
dimensioned for the current draw of the machine.  
 

 

1200W 220-240V EU / 1050W 100-130V US 

 

1550W 220-240V EU / 1450W 100-130V US 

 

2100W 220-240V EU / 1800W 100-130V US 

 
Check that the local AC voltage is appropriate, as indicated on the machine’s 
serial number label. If your AC voltage is outside the appropriate range, do not 

use the machine. Contact Martin™ Service for assistance. 
 

Se tt ing  up 

Fill the fluid tank with an approved Martin™ fog fluid as shown on page 21. If 
DMX control is being used, connect the machine to the DMX line (see page 19). 
 
If you are using several machines from one control panel in master-slave link 
mode, link the machines in a daisy-chain using the DMX input and output 
sockets. It does not matter which socket is used as input or output. 
 

Final c hec ks  

Before applying power to the machine, verify the following: 

 

the machine is safely located or installed and meets the location 
requirements stated on page 13 

 

the operator is familiar with, and able to comply with, the requirements 

for safe operation listed on page 5. 

 

the fluid is one of the Approved Martin™ fluids listed under “Approved 
fluid types” on page 21. 

 

the machine is electrically grounded (earthed) 

 

the AC power distribution circuits and lines are adequately rated for the 

current load 

 

Turning  on t he  powe r  

Set the mains switch on the rear of the unit, to the ‘ON’ (I) position. The display 
will show 

HEAT

. If the display shows 

OFF

, press the 

FOG

 button on the control 

panel or set the 

RUN MODE

 to 

CONTINUOUS

. After about 6-8 minutes if no 

DMX is connected the display should show 

FOG LEVEL 

(along with the set 

output level) and the machine will begin producing fog. If DMX is connected the 
display will show 

DMX

 when the machine is ready. 

 
The machine will remember its state from when it was turned off last time, so it 
will only power up in OFF mode if you have previously disabled the heaters. 

 

 

To obtain maximum output, wait another few minutes after the READY 
indication is shown, as the machine continues to heat to full operating 
temperature and fog output is reduced while the unit is heating up. 

 

 

Summary of Contents for JEM ZR series

































Reviews: