Martin 90523000 User Manual Download | Manualshive

Page: 9 / 41

background image

Installation

9

The FiberSource CMY150 is equipped with a 1.8-meter (5.9 ft.) length of 3-
conductor 0.75 mm

2

(~18 AWG) electrical cable for connection to the AC power

supply. The cable attaches with 1/4” female spade plugs on the live and neutral
wires and a ring terminal on the ground wire. Other cable can be installed as
follows.

R e p l a c i n g t h e m a i n s l e a d

1 Isolate the fixture from AC power.

2 Remove the fixture housing.

3 Disconnect the existing mains cable and pull it through the hole in the chassis.

4 Pass the new cable through the hole in the chassis and connect the leads. The live

wire connects to PL3, the neutral wire connects to PL1, and the ground wire connects

to the chassis screw terminal.

5 Draw up the slack in the AC and data cables and replace the fixture housing.

I n s t a l l i n g a c o r d c a p o n t h e m a i n s l e a d

A cord cap may be installed on the mains lead for testing, service, and temporary
applications.

Following the cord cap manufacturer’s instructions, connect the yellow and green
wire to ground (earth), the brown wire to live, and the blue wire to neutral. Table 3
shows some pin identification schemes; consult an electrician if you have any
doubts about proper installation.

F I B E R O P T I C C A B L E

Fiber optic cable is connected to the FiberSource CMY150 using one of the
available fiber adaptor kits:

• P/N 91611035, for 75-350 x Ø1mm fibers. This has a diameter of 30mm and is

supplied with an adaptor ring that increases the adaptor diameter to 38mm so that it
will fit in the port of the FiberSource CMY150 fixture.

• P/N 91611034, for 350-800 x Ø1mm fibers. This has a diameter of 38mm.

Wire (EU)

Wire (US)

Pin

Marking

Screw (US)

brown

black

live

“L”

yellow or brass

blue

white

neutral

“N”

silver

yellow/green

green

ground green

Table 3: Cord Cap Connections

«
...
7
8
9
10
11
...
»

Summary of Contents for 90523000










































Reviews:

No comments

Related manuals for 90523000

Brand: Wattle Pages: 6

Brand: Baicells Pages: 8

Brand: Xinje Pages: 57

FRDM-STBC-SA9500

Brand: Freescale Semiconductor Pages: 2

BladeCenter Management Module

Brand: IBM Pages: 184

Brand: JETWAY Pages: 55

Brand: Tbus Pages: 25

Brand: Faderfox Pages: 10

SmartNode 4520 Series

Brand: Patton electronics Pages: 90

Brand: Techroutes Pages: 20

IPS Pro-Module-24C-GE-BP-TM

Brand: Trend Micro Pages: 3

Brand: Westermo Pages: 34

Brand: NETGEAR Pages: 20

GlobeSurfer X-1

Brand: Option Audio Pages: 30

Brand: Qlogic Pages: 2

Brand: Hama Pages: 7

ExtremeCloud Appliance E1120

Brand: Extreme Networks Pages: 219

Brand: LevelOne Pages: 142

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands