MARSAL MB236 Installation & Operating Manual Download Page 5

DELIVERY

Marsal & Sons, Inc. cannot assume responsibility for loss or damage suffered in transit. The 

carrier assumed full responsibility for delivery in good order when the shipment was accepted. 

We are, however, prepared to assist you if filing a claim is necessary. 

OVEN LOCATION

The oven should be installed in a location in which the facilities for ventilation permit satisfactory 

combustion of gas and proper venting. The oven should be located so as not to interfere with 

proper circulation of air within the confined space. In buildings where normal infiltration does 

not provide the necessary air, outside air should be introduced. 

It is essential that an adequate air supply to the oven be maintained to provide a sufficient 

flow of combustion and ventilation air.

Place the oven in an area that is free of drafts.

Do not place the oven on a curb base or seal to a wall. This will restrict the flow of air and 
prevent proper ventilation. Pilot outages or yellow, floating flames on the main burners 
are indicative of a lack of secondary air.

Before making any utility connections to this oven, check the rating plate to be sure the oven 

specifications are compatible with the gas and electrical services supplied for the oven. The 

rating plate is located on the inside of the control door. 

ADJUSTMENTS ASSOCIATED WITH INITIAL INSTALLATION

Each  oven,  and  its  component  parts,  have  been  thoroughly  tested  and  inspected  prior  to 

shipment. However, it is often necessary to further test or adjust the oven as part of a normal 

and  proper  installation. These  adjustments  are  the  responsibility  of  the  installer,  or  dealer. 

Since these adjustements are not considered defects in material or workmanship, they are not 

convered by the Original Equipment Warranty. They include, but are not limited to:

calibration of the thermostat

adjustment of the doors

burner adjustments

leveling

testing of gas pressure

tightening of fasteners

No installation should be considered complete without proper inspection, and if necessary, 

adjustment by qualified installation or service personnel. 

3

Summary of Contents for MB236














Reviews: