Marpac 7-1545 Owner'S Installation & Operations Manual Download Page 13

12 

Page 

Section VI  

Maintenance: 

1.  The windlasses come with a grease lubricated gear box. There is no 

need for extra lubrication. 

2.  In order to make the windlass perform at optimize capacity and ex-

tend its life, use fresh water to wash off  salt water after each use. 

3.  Periodically check the electric joiner and the silicon sealant.   

Section VII  

Warranty: 

1.  The warranty is deemed as effective only under conditions of normal 

operation, maintenance and without modification of the product. 

 
2.  CLAIMS                                                                                                

If the product needs servicing, please send it back (or bring it to us) 
with the proof of purchase and we will investigate the product free of 
charge before repairing. However, the cost of postage or removal 
from the boat will be borne by the owner. 

 
3.  LIMITATIONS AND EXCLUSIONS                                                      

The warranty will be deemed effective only if the windlass is used 
on a non-commercial basis and will be invalid and excludes the fol-
lowing conditions. 
a. 

Operation exceeds the stated specifications 

b. Use 

for 

purposes 

other than indicated 

c. 

Disassembly or modification of the product 

d. Installation 

of 

other parts on the product. 

e. 

Third party products even if associated or used together with 
this product. 

Summary of Contents for 7-1545

















Reviews: