Market Forge Industries STHE-12-TGG Installation And Operation Manual Download Page 2

Page: 2 / 47

INSTALLATION AND OPERATION MANUAL AND PARTS LIST,

MODELS: STHE-7-TGG, STHE-12-TGG, STHE-16-TGG

PART NUMBER 10225R0

2010-09-07

IMPORTANT NOTES FOR INSTALLATION AND OPERATION

Retain this manual for future reference.

NOTICE

Instructions to be followed in the event that the operator of this appliance

smells gas must be posted in a prominent location. This information shall be

obtained by consulting the local gas supplier.

IMPORTANT

Do not attempt to operate this unit in the event of power failure.

Adequate clearances must be maintained for safe and proper operation.

The appliance area must be kept free and clear of combustibles.

Do not obstruct the flow of combustion and ventilation air.

Contact the factory, the factory representative or a local service company to

perform maintenance and repairs should the appliance malfunction. Refer to

warranty terms.

Summary of Contents for STHE-12-TGG
















































Search results

Summary of Contents for STHE-12-TGG

Reviews:

Related manuals for STHE-12-TGG

Brands by name

Popular brands

Market Forge Industries STHE-12-TGG, Installation And Operation Manual

Search results

Summary of Contents for STHE-12-TGG

Reviews:

Related manuals for STHE-12-TGG

Brands by name

Popular brands