Figure 1
Figure 3
Figure 4
Figure 2
SHAVING
BLADE
ICE
DEFLECTOR
Figure 5
Figure 6
Figure 7
SHAVING BLADE
-11-
-12-
IMPORTANT: YOUR ICE HOPPER COMES WITH ONE OF TWO
TYPES OF SHAVING BLADE ASSEMBLIES
a.
Shaving blade assembly nut
b.
Ice deflector blade assembly
PLEASE FOLLOW THE BELOW INSTRUCTIONS TO
SAFELY REMOVE THE SHAVING BLADE ASSEMBLY
FROM THE ICE HOPPER
4a.
Turn the shaving blade assembly nut counter
clockwise (to the left) and remove, then remove the
Shaving Blade and store in a safe place
4b.
To remove the ice deflector blade assembly, push and
slide the u-lock upwards and pull the ice deflector blade
from the ice hopper and store in a safe place.
BE SURE TO RINSE THE SHAVING BLADE AND DRY
THOROUGHLY BEFORE STORAGE
5.
Carefully lift the Glass Blending Jar straight up to
remove. The Ice Chute is spring-loaded and can be
pushed up. If the Bending Jar is not easily removed,
rock gently and lift. Do not twist.
Figure 6
6.
Turn the Blending Jar upside down and unscrew the
Jar Base counter clockwise (to the left). Carefully
remove the Blending Blade, and Blending Blade
Sealing Ring.
WARNING: THE BLENDING BLADE IS SHARP.
HANDLE WITH CARE.
7.
To remove the Ice Melt Reservoir hold the unit still
and pull straight out on the handle.
Figure 7
8.
The Ice Reservoir Lid, Ice Reservoir, Shaving Paddle,
Ice Hopper, Shaving Blade Assembly Nut, Shaving
Blade, Blending Jar Lid, Blending Jar, Blending Blade,
Blending Blade Sealing Ring, Jar Base and Ice Melt
Reservoir can be safely washed in the top rack of your
dishwasher. Use only top rack. Failure to do so
will result in damage.
9.
Use a damp cloth to clean the outside of the unit.
WARNING: UNPLUG UNIT BEFORE CLEANING. DO NOT USE
SOLVENTS. NEVER IMMERSE THE UNIT IN WATER.
10.
Clean the inside walls of the ice chute with a damp cloth
after every use.
IMPORTANT: Your Blending Jar, Shaving and Blending Blades are subject to
wear during normal use. Always inspect for nicks, chips, or cracks. Always
inspect for broken, cracked, or loose blades. If the jar or Shaving and Blending
Blades are damaged, do not use. Call our toll-free customer service number,
1-800-667-8623, to obtain replacement parts.
1.
Make sure unit is unplugged. Place on a clean dry
surface. Turn the unit so the back is facing you. Push
down on the Ice Reservoir Release Button. Lift the back
of the Ice Reservoir and remove. This will expose the
Shaving Paddle and Ice Hopper.
Figure 1
Note the location of the Shaving Blade inside
the Ice Hopper.
Figure 2
WARNING: DO NOT PLACE FINGERS INSIDE
THE ICE HOPPER NEAR THE SHAVING BLADE.
BLADE IS SHARP HANDLE CAREFULLY.
2.
To Remove the Shaving Paddle: Press the button
located behind the Ice Chute. If the button cannot be
pressed, rotate the Shaving Paddle for a half turn and retry.
While pressing the button, rotate the Shaving Paddle
counter-clockwise
(to the left) by placing fingers in the
ridges of the Shaving Paddle and unscrew. This will
expose the Ice Hopper and Shaving Blade.
Figure 3
To re-assemble the Shaving Paddle, simply replace it
into the threaded insert and rotate clockwise. Hand
tighten only.
3.
Press the two Ice Hopper release catches and lift the
Ice Hopper to remove.
Figure 4
4.
Remove the ice deflector blade assembly by pushing
and sliding the u-lock upwards. Pull the ice deflector
blade from the ice hopper and store in a safe place.
Figure 5
Cleaning and
Maintenance
DM2000-033_12EFM1.indd 11-12
7/19/12 9:41 AM
