March Pumps TE-7R-MD, Installation Instructions & Repair Parts, Page: 2 / 2

REPAIR PARTS
USED IN ITEM DESCRIPTION QTY. PART NO.
All 7s 1 Screw – Stainless 6 0155-0014-1000
7R, 7K 2 Washer – Stainless 6 0155-0021-1000
7R 3 Front Housing – Polypropylene 1 0155-0011-1000
7K 3A Front Housing – Kynar
®
1 0155-0125-1000
7S 3B Front Housing – 316 Stainless 1 0155-0036-0000
All 7s 4 “O” Ring – Viton
®
1 0155-0010-1000
All 7s 5 Washer – Ceramic 1 0155-0009-1000
7R, 7K 6 Shaft – Ceramic 1 0155-0039-1000
7S 6A Shaft – Ceramic 1 0155-0117-1000
7R 7 Impeller Assembly – Polypropylene (w/Teflon
®
/ Ryton
®
Bushing) 1 0155-0159-0500
7K 7A Impeller Assembly – Kynar
®
(w/Carbon Bushing) 1 0155-0160-0200
7S 7B Impeller Assembly – 316 Stainless (w/Carbon Bushing) 1 0155-0112-0400
7R 8 Rear Housing – Ryton (w/Rear Ceramic Thrust Washer) 1 0155-0067-0100
7K 8A Rear Housing – Kynar (w/Rear Ceramic Thrust Washer) 1 0155-0124-0100
7S 8B Rear Housing – 316 Stainless 1 0155-0035-0000
All 7s 9 Drive Magnet Assembly 1 0155-0130-0200
All 7s 10 Motor to Pump Connecting Bracket – Ryton 1 0155-0092-0100
7R, 7K 11 Motor – TEFC – ¾ H.P. – 1 Phase – 115/230 Volts 1 0155-0016-1000
7R, 7K 11A Motor – TEFC – ¾ H.P. – 3 Phase – 208/230/460 Volts 1 0155-0022-1000
7S 11B Motor – TEFC – 1 H.P. – 1 Phase – 115/230 Volts 1 0155-0173-1000
7S 11C Motor – TEFC – 1 H.P. – 3 Phase – 208/230/460 Volts 1 0155-0174-1000
All 7s 12 Washer – Stainless 4 0155-0019-1000
All 7s 13 Screw – Stainless 4 0155-0017-1000
1819 PICKWICK AVE., GLENVIEW, IL 60026-1306, U.S.A
PHONE: (847) 729-5300 · FAX: (847) 729-7062 · www.marchpump.com
0155-0046-1000 R13
March pumps are guaranteed only against defects in workmanship or materials for a period of one year from date of manufacture
pumping water. On all other solutions, contact the factory for application assistance. March Pump Application Worksheet 750-130-
10 is available for additional warranty information.
LIMITED WARRANTY
Alternate materials are available. Contact the factory for assistance in determining the best
recommended materials for your particular applications.
NOTE: When replacing Impeller Bushing in the field:
The plastic bushing must be bored to size after they have been pressed into the
impeller. Bore to .378/.381 I.D. The carbon and ceramic bushings are to finished size
and do not require boring.
When attaching drive magnet (item 9) to the motor shaft, position the face of the drive
magnet 1/16 inch below the face of the motor bracket (item 10)