31
ENGLISH
BASS PEAK LEVEL
With Dolby Digital and DTS , not only the LFE (Low Frequency
Effects), but also the bass of all channels can be heard from the
Subwoofer or Large-speakers. This procedure prevents these
speakers from becoming too loud and creating an unbalanced sound.
Since the sound is output at a loud volume, perform this operation
carefully.
Note:
• If your system does not include a subwoofer, this setting will set
the bass peak level for your front speakers.
TEST SIGNAL:
Press the
OK
or
Left
button, START is indicated and
it begins to generate a Bass test tone from the
speaker which was designated “bass signal output”
during setup.
There will be no audible sound yet because the
Master volume is set to minimum automatically.
Press
Down
cursor button to move the cursor to
VOLUME control.
VOLUME:
Adjust the bass test tone output level up until the
bass begins to distort or you reach the maximum
level with the
VOL+
,
VOL–
or
Right
/
Left
cursor
button.
Press
Down
cursor button to move the cursor to
ENTER.
ENTER:
Press the
OK
button, ENTER will blink and stop
generating the Bass Peak test tone.
The Bass Peak Limit Level for your system has now
been memorized.
If you finish these setup, move cursor to “MAIN” with
Up
or
Down
cursor button and then press
OK
button to go to MAIN menu.
Notes:
• Each time the subwoofer level is changed, perform the Bass
Peak Level setup and correct the setting.
• The bass peak level is not available in SOURCE-DIRECT and
7.1CH-INPUT mode.
• The selected value is displayed in the volume column before the
test signal starts.
2 - 4
B A S S
P E A K
L E V E L
B A S S
P E AK
T E S T
:
S T AR T
VO L UME
L E V E L
:
+ 1 8 d B
- - - - - - - - - - - - - - - - - - - -
E N T E R
MA I N
R E T U RN
E X I T
PREFERENCE
1.
Select “
PREFERENCE
” in
MAIN SETUP MENU
with
Up
or
Down
cursor button, and press the
OK
button.
2.
To select a desired content, press
Up
or
Down
cursor button.
TV AUTO:
Select the TV AUTO ON/OFF function to enable or
disable with
Left
or
Right
cursor button.
(refer to page 40)
OSD Info:
Select the OSD information function to enable or
disable with
Left
or
Right
cursor button.
If you select “
ENABLE
”, SR9200 will display the status
of the feature (Volume up/down, input select, etc..) on
the TV monitor. But if you do not desire this
information, select “
DISABLE
“.
DIG. OUT:
Select the digital source to output the DIGITAL OUT
terminals with
Left
or
Right
cursor button.
This is for digital dubbing to a CD-R recorder or MD
deck. (See page 41)
The source is switched in the following sequence.
SOURCE
→
DIG.1
→
DIG.2
→
→
→
DIG.8
→
DIG.9
→
AUX
→
OFF
→
SOURCE
→
SUB-W OUT: “THX”
position is required, but If you desire an
additional front L/R mixed subwoofer output in the
STEREO mode, select
“L/R MIX”
with
Left
or
Right
button.
If you finish the setup in this item, move cursor to “
MAIN
” with
Up
or
Down
cursor buttons and press
OK
button.
3
P R E F E R E N C E
T V - AU T O
:
D I S A B L E
O S D
I N F O
:
E NAB L E
D I G I T A L
OU T
:
SOUR C E
S UBWOOF E R OU T
:
T H X
MA I N
E X I T
