10
5. Press the rec/pause control button. The REC indicator will begin
to flash indicating the tape transport is in the record pause
mode.
6. If the ALC control button is in the Off position, using the manual
record level control adjust the input signal to the desired
recording level.
7. Press the
5
play control button to begin recording in the forward
direction. Press the
4
play control button to begin recording in the
reverse direction. When the tape enters into the playback mode
the REC indicator and the play control button indicator will
change from the flashing mode to the constant on mode.
Thisindicates the tape transport is in the record mode.
8. To pause the tape transport during recording press the rec/
pause control button. Press the play control button to resume
recording.
9. Pressing the stop control button will stop the tape transport
during recording. Pressing the
1
rewind in the
5
play/record
direction or the
2
FAST FORWARD in the
4
play/record direction will cause the
unit to return to the position the recording began at.
COMPACT DISC PLAYER OPERATION
COMPACT DISC PLAYBACK
1. Open the compact disc tray by pressing the STOP/EJECT
button. Load a compact disc onto the compact disc tray and
close the tray by gently pushing the front of the compact disc
tray or by pressing the STOP/EJECT button. The CD player
display will show the general data of the current CD.
2. To begin playback of the compact disc press the CD play/pause
control button. The
5
indicator in the CD PLAY/PAUSE button
will illuminate, the display will show the data for the first track
and the track will begin to play.
3. To pause the CD during playback, press the CD PLAY/PAUSE
button. The display will remain in the current position and the
5
indicator in the CD PLAY/PAUSE button will begin to flash.
Pressing the CD PLAY/PAUSE button will resume normal
playback from the point that the CD player was paused.
4. Upon completion of playback of the last track in the disc the CD
Player will return to the stop mode. You can also stop the CD
playback by pressing the STOP/EJECT button once.
Pressing the STOP/EJECT button again will cause the CD tray
to open.
SELECTING THE TRACK FOR PLAYBACK
1. By pressing the CD
7
NEXT or the CD
6
PREVIOUS buttons you
can select the track to be played. Each press of the CD
7
button
will advance the CD player to the beginning of the next track and
enter into the play pause mode.
Each press of the CD
6
button will cause the CD player to skip
to the beginning of the previous track and enter into the play
pause mode. Pressing the CD PLAY/PAUSE button will resume
playback at the beginning of the selected track.
PROGRAMMING PLAYBACK TRACKS
(PROGRAM PLAY MODE)
This procedure allows you to program selected tracks for playback
in the order you desire.
1. By pressing the PROGRAM button once you will place the CD
player into the programming mode for playback. Once the
PROGRAM button is pressed the PROGRAM indicator in the
CD display will begin to flash. This indicates the CD player is in
the program entry mode.
2. By pressing the CD
7
NEXT or the CD
6
PREVIOUS buttons you
can select the track to be programmed. Each press of the CD
7
button will advance the CD player to the beginning of the next
track. Each press of the CD
6
button will cause the CD player to
skip to the beginning of the previous
t r a c k . W h e n t h e
desired track number has been selected, leave the CD player
untouched for approximately 1.5 seconds and the selected
track will be stored in the playback program. Continue this
procedure until all desired tracks(20 tracks maximum) have
been programmed.
3. By pressing the PLAY/PAUSE button the CD player will exit the
program entry mode and enter the program play mode. The
PROGRAM indicator in the CD display will go to constant on and
the CD player will begin to play in the order selected during the
programming.
4. By pressing the STOP/EJECT button the CD player will stop
playing but will remain in the program play mode. The program
will remain in memory.
5. When the STOP/EJECT button is pressed while the CD player
is in the stop mode and while the program is still engaged, the
memorized program will be cleared.
CD TO TAPE DUBBING
The CD source can be dubbed directly on to the tape deck by two
means, manual recording or automatic level control(ALC On).
During manual record dubbing the level desired is adjusted by
manually adjusting the record level control. After the desired level
is adjusted, you then release the tape deck to record. During ALC
dubbing the record level is adjusted automatically based on the
peak levels of the source and the tape deck enters the dubbing
mode automatically.
MANUAL LEVEL TAPE DUBBING
1. By pressing the CD STOP/EJECT button and the tape eject
button you can load the CD to be dubbed onto the CD tray and
a recordable tape into the tape transport. Gently press the front
of each of the mechanism to close them. The CD display will
register the general CD data and the tape play indicator located
inside of the tape PLAY button will begin to flash.
2. Prepare the tape for dubbing by rewinding it to the beginning of
the first side that the tape is to be recorded onto.
3. Set the ALC switch to the OFF position.
4. Press the DUBB button once. The REC indicator will begin to
flash, the DUBB indicator will light and the CD player will enter
play mode. At this point you can adjust the record level control
to achieve the desired record level.
5. After adjusting the record level, press the DUBB button again.
The CD player will return to the stop mode, and the tape
transport will enter into the record mode. After approximately 5
seconds the CD player will enter the playback mode and begin
to play the first track, dubbing it onto the tape.
6. When either the CD transport or the tape transport have
reached the end and stopped, the other transport will also stop.
7. To end the dubbing during a session, press the STOP on the
tape transport or the STOP/EJECT button on the CD player.
