background image

CAUTION

RISK OF ELECTRIC SHOCK DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, 

DO NOT REMOVE COVER (OR BACK) NO USER-SERVICEABLE PARTS 

INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL

The lightning fl ash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence 
of uninsulated “dangerous voltage” within the product’s enclosure that may be of suffi cient magnitude to constitute a 
risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important 
operating and maintenance (servicing) instructions in the literature accompanying the product.

WARNING

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO 
RAIN OR MOISTURE.

CAUTION:

 

TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY 

INSERT.

ATTENTION:

 

POUR EVITER LES CHOCS ELECTRIQUES, INTRODUIRE LA LAME LA PLUS LARGE DE LA 
FICHE DANS LA BORNE CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU’AU FOND.

NOTE:

This equipment has been tested and found to comply with 
the limits for a Class B digital device, pursuant to Part 15 
of the FCC Rules. These limits are designed to provide 
reasonable protection against harmful interference in a 
residential installation. This equipment generates, uses and 
can radiate radio frequency energy and, if not installed and 
used in accordance with the instructions, may cause harmful 
interference to radio communications. However, there is 
no guarantee that interference will not occur in a particular 
installation. If this equipment does cause harmful interference 
to radio or television reception, which can be determined by 
turning the equipment off and on, the user is encouraged to 
try to correct the interference by one or more of the following 
measures:

-  Reorient or relocate the receiving antenna.

-  Increase the separation between the equipment and 

receiver.

-  Connect the equipment into an outlet on a circuit different 

from that to which the receiver is connected.

-  Consult the dealer or an experienced radio/TV technician 

for help.

NOTE:

Changes or modifications may cause this unit to fail to 
comply with Part 15 of the FCC Rules and may void the 
user's authority to operate the equipment.

This Class B digital apparatus complies with Canadian 
ICES-003.

Cet appareil numerique de la Classe B est conforme a la 
norme NMB-003 du Canada.

PM-KI-PEARL̲UN̲cover etc.indd   Sec2:1

PM-KI-PEARL̲UN̲cover etc.indd   Sec2:1

09.7.10   11:16:41 AM

09.7.10   11:16:41 AM

Summary of Contents for PM-KI PEARL


































Reviews: