background image

3-3. Operation Info Mode

3-3.1. Actions

This mode enables the unit to display the accumulated operating time, power On count and each pro-

tection count.

3-3.2. Starting up

While holding down buttons "

ZONE2 SOURCE

" and "

STATUS

" simultaneously, press the power button 

to turn on the power.

Select the "

4. OP INFO

" using the "

INTERNET RADIO

" button, then press the "

STATUS

" button then to 

confirm.

3-3.3. Operations

Press the "

STATUS

" button after starting up this device in Operation Info mode.

The following information is displayed in the following order.

(a)   Accumulated operating time

OP Time  ______H

                   

 

↑ Time display

              "

STATUS

"

(b)  Power On count

P.On Time______ 

                   

 

↑ Count display

              "

STATUS

"

(c)   DC / ASO Protection count

DC:___/ASO:___  

              "

STATUS

"

(d)  Thermal Protection (A/B) count

THM A:___/B:___ 

              "

STATUS

"

(e)   Thermal Protection (E/F) count

THM E:___/F:___ 

              "

STATUS

"

(f)   Current Protection count

Current:___     

              "

STATUS

"

    (Returns to normal display)

3-4. TUNER STEP mode (U / N only)

3-4.1. Actions

This is a special mode for enabling reception STEP of the ANALOG TUNER to be changed.

3-4.2. Starting up

While holding down buttons "

ZONE2 SOURCE

" and "

STATUS

" simultaneously, press the power button 

to turn on the power.

Select the "

5. TUNER FRQ SET

" using the "

INTERNET RADIO

" button, then press the "

STATUS

" but-

ton then to confirm.

3-4.3. Displays

Start up this unit in TUNER STEP mode, select the desired option using the "

INTERNET RADIO

" button, 

then enter using the "

STATUS

" button.

The following information is displayed in the following order.

(a)   AM9 kHz / FM50 kHz is selected

 <  AM9/FM50  > 

             
    "

INTERNET RADIO

 

"

ZONE2 SOURCE

"

(b)  AM10 kHz / FM200 kHz is selected

 < AM10/FM200 > 

             
              "

STATUS

"

(c)   Press the power button to turn off the power.

(d)  Press the power button to turn on the power.

114

Caution in 

servicing

Electrical

Mechanical

Repair Information

Updating

Summary of Contents for NR1607


























































































































































Reviews: