Marantz NA6006 Service Manual Download Page 61

Page: 61 / 69

PROCEDURE AFTER REPLACING THE U-COM, ETC.

The procedure after replacing the u-COM (microprocessor) is as follows.

Implement the update method when the MAIN PCB or network module is replaced.

PCB Name Ref. No.

Description

Procedure

after Re-

placement

Remark

MAIN

U3001 R5F5631FDDFB

SOFTWARE : System

MAIN

U3013 5M570ZF256C5N

SOFTWARE : AUDIO PLD

MODULE U3010 NETWORK MODULE

SOFTWARE : Network

China region only

MAIN

U3005 GD25Q32B

SOFTWARE : China font

Procedure after Replacement

A :

The software has been written. The software is not written at the time of replacement.

B :

The software has been written. The software may need to be rewritten by version updates. Check the

version.

C :

The software has not been written. The software needs to be written after replacement.

See "

FIRMWARE UPDATE PROCEDURE

" for information on writing the software.

D :

The software has been written. Be sure to replace the software with the latest version.

See "

3. Update method when the MAIN PCB or network module is replaced (Using a USB flash drive

U3001, U3013, NETWORK MODULE)

" for information on rewriting the software.

PROCEDURE AFTER REPLACING THE PCB.

The procedure after replacing the printed circuit boards is as follows.

(1) Change the resistor for setting the region.

Model Area

MAIN PCB

R3035

R3033

R3034

R3032

R3030

R3031

North America (U)

10K

OPEN

Europe (N)

10K

OPEN

27K

2.7K

OPEN

Japan (F)

10K

OPEN

CHINA (K)

OPEN

10K

OPEN

See the PCB below.

(2) Be sure to replace the software with the latest version.

R31

R3120

R31

R3121

R3035

R3034

R3031

R3032

L3005

C3131

L3008

C3142

R3016

R3023

C3036

L3004

R3191

C3090

C3096

R31

C3006

R3228

R3192

C3138

R3195

L3006

C3203

C3202

C3220

R3138

R3140

R3145

R3160

R3153

R3152

R3167

C3216

C3205

Q3012

Q3011

R3310

R3319

C3206

X3002

C3236

C3229

L3026

L3025

L3024

L3009

C3054

C3237

C3238

C3240

C3231

R3043

R3033

R3064

R3059

R3051

R3047

R3050

R3083

R3088

R3079

R3089

R3092

R3096

R3097

R3072

R3020

C301

R3018

C3010

R3076 C3071

C3074

R31

R3109

C3085

C3133

C3130

C3136

C3137

R3214 R3213

R3017

R3024

C3158

R3223

R3224

R3225

C3104

L3003

D3003

Q3005

C3037

R3202

R3199

C3051

R3158

R3165

R3166

C3081

R3156

R3155

C31

R3144

R3150

C3243

C3244

C3004

C3005

R3029

C3082

R3022 R3026 R3025

C3157

R3231 R3229

C3144

C3167

R3232

C3089

C3124

L301

R3322

L3010

C3091

C3092

R3185

R3184

R3189

C3126

R3190

C3127

C3219

C3212

R3168
R3159

R3139

R3146

C3200

C3201

C3234

C3215

R3452

Q3013

Q3014

R3284

R3283

L3012

R3324

R3325

R3320

R3321

R3285

C3209

C3210

R3250

R3308

R3302

D3008

L3013

R3256

R3255

R3254

R3253

R3317

R3318

C3235

C3228

L3023

R3259

C3173

C3170

C3171

C3169

C3041

CN3001

C3060

R3065

R3103

R3101

R3102

R3098

R3099

R3036

R3037

R3038

D3004

C3050

R3517

R3230

C3115

3111

C3109

R3433

R3432

R3424

R3434

R3440
R3445
R3443
R3449

R3289

R3287

R3288

R3290

R3295

R3294

R3293

D3000

C3015

C3017

C3029
C3024

C3023

C3031

C3026

C3025

R31

R3107

R3108 R3106

R3085

R3090

R3094

R3077

R3019

R3000

U3003

R3030

D3001

C3242

C3129

L3007

C3140

R3471

R3475

R3478

R3476

R3477

R3497

R3481

R3482

R3196

R3197

Q3009

R3210 R3198

R3203

C3049

R3355
R3356

R3354

R3468

R3352

R3351

R3350

R3348

R3347

R3346

R3345

R3342

R3193

R3200

R3217

R3207

C3145

R3201

C3139

R3194

R3220

R3219

R3233

C3166

U3011

R3300

C3218

C3213

L3020

R3403

R3402

R3401

R3400

R3397

R3396

C31

R3234

C3168

R3332

R3435

R3330

L3019

R3450

C3226

R3305

R3304

R3303

R3315

R3313

C3196

C3172

C3174

R3245

R3242

R3246

R3249

R3247

R3248

R3237

R3238

R3235

R3239

R3241

C3043

C3239

C3233

C3232

L3002

C3009

C3008

L3001

C3019

C3014

C3030

C3032

C3020

C3016

R3040

R3516

U3005

R3070

R3063

R3058

R3046

R3049

R3095

R3075

R3082

R3078

R3100

R3087

R3091

C3084

C3070

R3081

R3086

U3004

U3002

R3021

Q3001

R3002

C3067

C3066

R3052

R3066

R3073

C3065

C3241

Q3003

R3472

R3473

R3469

R3470

R3474

C3141

C3132

C3128

C3134

C3135

C3143

C3148

C3149

R3211

R3499

R3500

R3498

R3480
R3479

CN3004

X3000

R3215

R3212

R3221

R3222

C3159

C3095

C3052

R3465

Q3007

Q3004

Q3006

R3111

R3157

R3151

X3001

C3083

R3113

R3122

R3028 R3027

D3002

R3161 R3162 R3163

R3147 R3148 R3149 R3142 R3143

C3101

C3094

R3001 C3000 R3015 R3014 R3013 R3012 R301

R3010 R3009 R3008 R3007 R3006 R3005 R3004 R3003

R3344

R3343

R3349

R3467

R3466

C3146 C3154 C3152

R3205

R3204

C3150

R3226

R3206

R3218

C3147

R3208

R3209

C3151

R3227

C3161

C3153

C3156

C3163

C3164

L3014

L3015

C3217

C3227

C3221

R3422

R3399

R3398

R3404

C3088

R3392

R3188

R3186

C3123

R3187

C3165

U3006

ADJ

ICT

L3018

L3017

C3230

PLATE1

C3207

R3329

R3436

R3437

R3448

R3446

SW3001

R3292

R3312

R3314

R3280

R3278
R3279

R3282

R3281

R3286

R3276

C321

R3306

U3014

U3016

Q3010

C3175

R3257

R3258

R3252

R3251

R3236

R3240

R3243
R3244

C3056

C3042

C3198

C3197

C3044

Q3000

R3071

R3093

Q3002

R3104

R3105

C3059

U3009

CN3011

SW3000

R3135

U3007

C3160

C3155

U3012

U3008

R3333

R3123

C3098

R3129

C3105

C3097

R3125

R3124

C3099

C3100

R3130

R3141

R3414

R3410

R3409

R3413

R3412

R3411

R3425

R3415

CN3009

R3327

U3017

R3341

R3326

R3336 C3214

C3204

R3323

C3222

C3223

C3224

C3225

L3021
L3022

CN3010

U3010

U3018

R3291

CN3007

C3208 R3331

C3013

C3021

C3022

C3027

R3484

R3485

R3486

R3487

R3490

R3492
R3491

C3057

C3058

R3495

R3496

R3501

R3060

R3055

R3054

R3053

R3504

R3069

C3061

C3062

R3057

R3062

R3056

R3041 R3045

R3183

C3120

R3182

C3119

R3178

R3177

R3179

R3416

R3417

R3391

R3390

R3389

R3388

R3338

R3334

R3335

R3378

R3377

R3376

R3297

R3296

R3328

R3372
R3373

R3374

R3371

R3311

R3367
R3368

R3366

R3365

R3359
R3360

R3362

R3361

R3271

R3274

R3273

R3275

R3263

R3262

R3261

R3277

R3154

C31

R3169

L3000

C3007

C3012

C3018

PLATE2

R3489

R3483

R3488

C3028

R3494
R3493

R3502

R3503

R3068

R3067

R3061

R3216

R3173

R3174

R3172

R3039

R3042 R3044

R3048

C3034

R3131

R3132

R3133

R3134

C3102

R3126

Q3008

R3180
R3181

C3103

R3170 R3171

R3298

R3299

R3339

R3340

R3337

R3363

R3369

R3364

R3370

R3375

R3353

R3260

R3264

2
3

5
6
7
8

13
14
15

11
12

U3013

C3055
C3053

D3009 D3007 D3006

C3125

C3033

C3162

U3001

CN3003

CN3000

C3108

CN3005

JACK3000

BKT3001

CN3006

U3000

BKT3000

CN3008

CN3002

EL_RD

EL_RST

OLED_D0

EL_DC

EL_RW

EXP_SCL

EXP_SDA

+5V2_SMPS

DIR2_DEMP DIR2_GPO

DIR2_ERR

P3V3_UCOM

P5V_NET

CS SO WP

P5V_D_USB

RST

ATA

PBCK

BKT3002

PBCK

MCK

DATA

DOUT

CLK

MCK

LRCK

DIR_NPCM

DIR_INT

3.TXD

100/16(RA2)

JSR2124

AK4458VN

JST2165

LEGO5V

NET3.3V

RST

I2S0_DA

TDM DA

LRCK

I2S2

BCK

ATA

I2S2

4.GND_D

2.GND_D
1.GND_D

8.GND_D

13.MUTE

P1V8_D

NET_PLD_

2.GND_D

1.GND_D

EL_CS

7.RL

Y_PWRA

6.PROTECT

5.P/D

4.+5V2_SMPS

8.A_PW_SHOR

BD4730G

GD25Q32B

P5V_D_OP

LRCK

3.GND_D

2.+3.3V_D

MCK

7.+5V_USB

6.GND_D

9.GND_D

8.+5V_USB

LRCK

12-+5V_D_A

ADC_PLD_

1.GND_D

4.EL_RD

2.GND_D

PBCK

7.EL_CS

6.EL_R

9.OLED_D6

8.OLED_D7

16.KEY1

2.+3.3V_CPU

1.RESET

18.KEY3

19.REMOTE

7.DSP_BOOT

6.CNVSS

5.GND_D

26.GND_D

25.GND_D

27.GND_D

USB_NOC

USBVBUSDR

SDA

I2C_SCL_CS2K

I2C_SDA_CS2K

6.GND_D

I2C_SDA_DIR2

I2C_SCL_DIR2

1.+3.3V_CPU

4.+5V_LEGO

3.EL_RESET

10.OLED_D5

14.OLED_D1

13.OLED_D2

12.OLED_D3

15.OLED_D0

20.OLED_P_CONT

22.LED_GREEN

21.LED_RED

PLD_NET_TDM_FS_SL.

NET_PLD_TDM_FS.

P3V3_D_PLD

7020-08281-000-0S

4.SMPS_GND
3.SMPS_P_DOWN
2.A_PW_CONT

5.D_PW_CONT

9.SMPS_GND
8.+5V2_SMPS
7.+5V2_SMPS

10SMPS_GND

PCF8574PWR

REGION

22/16(RA2)

BKT3004

N5V_D_OPA

R5F5631FDDFB

10MHZ

TXD_MOEI

CTS_MIEO
RTS_MOEI

RXD_MIEO

10/50(KR3)

P3V3_D_AUDIO

DIR1_PLD

INT/EXT

DIR_CE

DIR_RESET

24.576MHZ

DIN

PCM9211

P5V_D_AUDIO

4.RXD

RC-5(OR/OR)

NJM8068G

(BLACK)

BKT3005

PLD_CONF_TDO

PLD_CONF_TDI

PLD_CONF_TCK

C_PLD_CLK.

C_PLD_MDO.

C_PLD_MDI.

C_PLD_CS.

BKT3003

DIR2_PLD_DATA.
DIR2_PLD_LRCK.
DIR2_PLD_PBCK.

P5V_D_SPDIF

(GRAY)

NET_FACT_RST

SN74LVC244APWR

PLD_DAC1_MCK
PLD_DAC1_PBCK/DBCK
PLD_DAC1_LRCK/DSDL
PLD_DAC1_DATA/DSDR

SCL

PLD_CONF_TDI

PLD_CONF_TMS

PLD_CONF_TCK

SN74LVC244APWR

MFI337S3959

C_TDM_CONV

RESET

22.5792MHZ(OSC)

I2S0_BCK.

I2S0_LRCK.

TDM_BCK_SL.

I2S0_DATA.

1.RLY_PWRA

6.SMPS_GND

11+3.3V_CPU

3.+5V2_SMPS

PCF8574PWR

10.+5V_D_A

LC89091JA-H

5.EL_DC

17.KEY2

100/25(RFO)

DATA

OPT IN

P5V_D_USB

PLD_CONF_TMS

DIR2_PLD_MCK.

DAC2_RESET

I2C_SDA_DAC2

I2C_SCL_DAC2

OPT OUT

PLD_CONF_TCK.

DATA_SL.

5.+5V_LEGO

11.GND_D_A

11.OLED_D4

24.LED_DISP_OFF

23.LED_DOUT_OFF

NET_PLD_TDM_DA

TA.

NET_PLD_TDM_BCK.

NA6006 MAIN PCB(MP)

3.PCMDATA/DSDR/SPDIF

CLP3000

11.HP_DET
10.GND_D

7.PCM/DSD BCK

9.DIR_MCK(LEGO CLK)

17.DAC_CLK_SEL
16.DAC_I2C_CLK
15.DAC_I2C_DATA
14.HP_ON/OFF

21.DAC_GPIO

20.VARI_ON/OFF
19.HP_GAIN_M

DIR1_PLD_MCK.

ADC_PLD_PBCK.
ADC_PLD_LRCK.

ADC_PLD_DATA.

DIR1_PLD_DATA.

DIR1_PLD_LRCK.

5M570ZF256C5N

NET_PLD_MCK.

NJM2845DL1-18

TC7WHU04FU-TRB

5.PCM_WCK/DSDL

12.DAC_RESET

18.HP_GAIN_H

DIR1_PLD_PBCK.

PLD_DIR1_MCK

MAIN PCB

R3033

R3031

R3030

R3034

R3032

R3035

Before Servicing

This Unit

Electrical

Mechanical

Repair Information

Updating

Summary of Contents for NA6006





































































Search results

Summary of Contents for NA6006

Reviews:

Related manuals for NA6006

Brands by name

Popular brands

Marantz NA6006, Service Manual

Search results

Summary of Contents for NA6006

Reviews:

Related manuals for NA6006

Brands by name

Popular brands