Mantis ComposTumbler CT01001 Assembly Manual Download Page 3

4

STEP 1: Lower Support Assembly

Select:

• 2 Lower Supports (item 1)

• 2 Support Spacers (item 2)

• 4 1/2” x 2” (1.3 x 5 cm) Bolts (item 7)

1)  Make sure you have removed the tie rods from inside the

support spacers.

2)  Fasten one support spacer to lower support section with

1/2” (1.3 cm) Bolt as shown in the adjacent photograph.

After orienting the other lower support section in

a position where the straight and smaller ended

uprights are diagonally opposite each other,

 fasten

this section to the opposite end of the support spacer

with 1/2” (1.3 cm) bolt.

3)  With lower support sections held upright, as above,

fasten the other support spacer in a similar manner with

2 additional 1/2” (1.3 cm) Bolts to form the assembly

shown in the adjacent photograph.

STEP 2: Upper Support Assembly

Select:

• 2 Upper Supports (item 4)

• 2 Support Spacers (item 2)

• 4 1/2” x 2” (1.3 x 5 cm) Bolts (item 7)

1)  With open end facing down, position one upper support,

parallel to a lower support spacer, over the upright

sections of the lower support assembly, and oriented so

that a small diameter end opposes a straight section.

 

(Note: Upper support sections (item 4 in adjacent photo)

must be at right angles to lower support sections (item

1 in adjacent photo) to result in sufficient strength and

stability to support the drum.)

2)  Slip the ends of the upper support fully into and over the

uprights of the lower support section. Repeat with the

second support.

3)  Fasten the support spacers to the upper supports,

following the same procedure used in Step 1.

4)  Now is the time to secure the 8 bolts that turn into the

support spacers. Using a 3/4” (19 mm) wrench, snugly

tighten each bolt to stabilize support frame.

Summary of Contents for ComposTumbler CT01001




























Reviews: