background image

SPECIFICATIONS 

Vacuum tube compliment:

 6922 x 2 (gain) plus 5687 (or 7044) x 4 (output buffers) 

Fuse type and ratings: 

 

 

100-120 VAC:  

1.5 Amp MDL slow-blow main 

230-240 VAC:  

0.75 Amp MDL slow-blow main 

Moving Magnet input impedance:

 

5-step

 

user adjustable via 

fi

 xed low-noise resistors. 

25, 50, 100, 200 and 47000 Ohms. 

Moving Coil input impedance:

 

5-step

 

user adjustable via multi-tap autoformer: 

25, 50, 100, 200 and 400 Ohms. 

Input Termination Capacitance:

 

Variable in 10 picofarad steps from 10 to 1100 pF. 
(1.1 nF). Residual input capacitance less than 40 pF. 

Gain Steps: 

4-step user adjustable, 50, 55, 60 and 65 dB active gain at 1 kHz referred to FIXED 

output jack, 10 k-Ohm load. Additional gain available via MC step-up autoformer. 

Deviation from RIAA curve: 

Less than +0.5 / -0.3 dB from 20 Hz to 20 kHz, any gain setting. 

Typically less than +/- 1 dB from 10 Hz to 100 kHz 

Inter-channel differential phase: 

Less than 4 degrees from 20 Hz to 20 kHz, any gain setting. 

Typically less than 2 degrees. 

Inter-channel differential gain: 

Less than +/- 0.5 dB from 20 Hz to 20 kHz, any gain setting. 

Dynamic Range:

 

 

101 dB @ 1 kHz, 1% THD 

200 Ohm source, 47 k-Ohm input, @55dB Gain 

             97 dB @ 1 kHz, 0.1% THD 

THD: 

                                                0.0042% at 1V output @ 1kHz

REMORA RF REMOTE:  

            controls motorized volume control functions, uses 9v battery

Maximum LINE input level:

         +30.6dBu @ 1kHz for an output of +29.3dBu @ 0.07% THD

                                                          26.5Vrms @ 1kHz for an output of 22.8Vrms @ 0.07% THD

Maximum Output:             

            +27dBm @ 1kHz with 3% THD into 100k-Ohm load 

FIXed Output impedance:             

150 Ohms. Minimum suggested load greater than 1500 

Ohms. 

VARIable Output impedance:

 

75 Ohms. Minimum suggested load greater than 600 Ohms. 

                                                               GAIN setting    Fixed Output               Vari O/P           
MM Noise (S+N+D) / (N+D):

 

50 dB: 

86 dB            108dB   99dB   86dB 

200 Ohm source, 47 k-Ohm input 

55 dB: 

84 dB            108dB   99dB   85dB 

A-weighted Referred to 2.54 mV 

60 dB:             80 dB            108dB   94dB   80dB 

rms @ 1 kHz 

65 dB:             75 dB            108dB   89dB   75dB 

 9:00   12:00  V/C FULL 

MC Noise (S+N+D) / (N+D):

 

50 dB: 

84 dB            108dB   98dB   85dB 

100 Ohm source, 100 Ohm input 

55 dB: 

80 dB            108dB   95dB   81dB 

A-weighted Referred to 0.5 mV 

60 dB:             75 dB            108dB   90dB   76dB 

RMS @ 1kHz and rated input Z 

60 dB:             70 dB            107dB   85dB   71dB

19

Summary of Contents for STEELHEAD RC




















Reviews: