background image

The open mesh design of the mic allows all the highs to reach the capsule 

unimpared and allows the engineer to choose if, when and how much pop screen 

is appropriate. Vocal “pops” may distort the capsule without a pop screen.  Air 

movement and wind can overload a good capacitor mic capsule much easier 

than loud levels.We strongly recommend a good 2 layer nylon pop screen with 

this mic on close vocals. A built in foam screen needs built in HF boost - not 

here. Of course, no Manley microphone would be complete without a genuine 

leather capsule protector which slips (and ties) onto the end of the microphone 

to protect the capsule when not in use. Each Reference Microphone is packaged 

complete in a sturdy case.  
The STEREO version of our GOLD REFERENCE microphone is identical 

in every respect to the MONO GOLD REFERENCE but with two complete 

systems installed in one case with the upper capsule being fixed and the lower 

capsule being continuously ROTATABLE through 90° for M-S and X-Y 

BLUMLEIN-STYLE coincident pair recording technique. Each capsule has its 

own continuously variable PATTERN control and individual -10dB PAD switch 

for close miking of extra-ordinarily powerful brass and other instruments. Also, 

due to the power and audio requirements of having two complete microphone 

systems in one housing, the stereo mic has a dedicated 4-pin power cable that 

goes to the base of the mic. Audio is carried out from a single jack that is then 

split into two separate XLR cables (see page 9 for details).

POWER SUPPLY

    

FRONT 

      

  BACK

          A 

             B      C   D       E        F

A. Power light: When power is on, this light will glow red. When power is off, this light will, 

in fact, not glow at all.

B. IEC Power Connector: Connector for AC power input.

C. Fuse Holder: Replace with 1A SLO-BLO fuse for 120V operation, or 1/2A SLO-BLO for 

220V. This PSU uses “half-sized” fuses.

D. Power Switch: Pressing this switch up will turn the supply on.

E. 6-pin Microphone Cable Input: Where the supplied power/audio cable is inserted.

F. XLR Out to Micpre: Where the XLR cable goes out to your very favorite micpre.

SPECIFICATIONS (GOLD SERIES) 

MICROPHONE TYPE:      DUAL LARGE DIAPHRAGM CAPACITOR 

POLAR PATTERNS:  

   CONTINUOUSLY VARIABLE 

DIAPHRAGM SIZE:  

   1 INCH ; 1.25 INCH OVERALL 

DIAPHRAGM THICKNESS:   

 

3 MICRON; GOLD SPUTTERED 

FREQUENCY RESPONSE:   

 

10 HZ to 30 KHZ,  AMPLIFIER to 60 KHZ 

MAXIMUM INPUT SPL:      150 dBSPL AT CAPSULE 

SENSITIVITY:  

    19mV/Pa 

AMPLIFIER TYPE:  

   2 TRIODE GAIN BLOCK LO Z OUTPUT 

ACTIVE COMPONENTS:   

 

(1) 12AX7LPS  TUBE   (2 for STEREO MICS) 

OUTPUT TYPE :  

   TRANSFORMER WITH FEEDBACK LOOP 

OUTPUT POLARITY:  

   BALANCED XLR,  PIN 2 HOT, PIN 3 LOW 

AMPLIFIER DISTORTION:   

 

LESS THAN .05 % 

AMPLIFIER NOISE:  

   TYPICALLY -120 dB EIN (TUBE DEPENDENT) 

BODY:  

     24 KARAT GOLD OVER MACHINED BRASS

8

A. Power light: 

When power is on, this light will glow red. When power is off,  

this light will, in fact, not glow at all.

B. IEC Power Connector:

 Connector for AC power input.

C. Fuse Holder: 

Replace with 250mA SLO-BLO fuse for 100-120V operation, 

or 125mA SLO-BLO fuse for 220-240V operation. This PSU uses 5x20mm 

fuses.

D. Power Switch:

 Pressing this switch up will turn the supply on.

E. 6-Pin Microphone Cable Input:

 Where the supplied power/audio cable is 

attached.

F: XLR Out to Micpre:

 Where the XLR cable goes out to your micpreamp.

(Reference Cardioid and Mono Reference Gold)

POWER SUPPLY

4

Summary of Contents for Cardioid












Reviews: