Manitowoc Marine Q800 Installation And Use Manual Download Page 22 | Manualshive

Page: 22 / 28

background image

Maintenance

Section 4

4-6

Water Pump

WARNING

Disconnect the electric power to the ice machine at
the electric service switch box and turn off the
water supply.

1.

Disconnect the water pump power cord.

Water Pump Removal

2.

Disconnect the hose from the pump outlet.

3.

Loosen the screws securing the pump mounting
bracket to the bulkhead.

4.

Lift the pump and bracket assembly off the
screws.

Ice Thickness Probe

1.

Compress the side of the ice thickness probe near
the top hinge pin and remove it from the bracket.

DISCONNECT

WIRE LEAD

SV1619

COMPRESS

HINGE PIN

TO REMOVE

ICE

THICKNESS

PROBE

Ice Thickness Probe Removal

NOTE: At this point, the ice thickness probe can
easily be cleaned. If complete removal is desired,
continue with step 2 below.

WARNING

Disconnect the electric power to the ice machine at
the electric service switch box.

2.

Disconnect the wire lead from the control board
inside the electrical control box.

SV1618

PUMP

OUTLET

WATER

PUMP

POWER

CORD

LOOSEN
SCREWS

«
...
20
21
22
23
24
...
»

Summary of Contents for Marine Q800





























Reviews:

No comments

Related manuals for Marine Q800

Brand: Panasonic Pages: 252

Brand: Gates Pages: 2

AJHVF21G - HD EVF - MULTI-LANG

Brand: Panasonic Pages: 4

Brand: A-Tach Mounts Pages: 2

Brand: A-Tach Mounts Pages: 2

Brand: A-Tach Mounts Pages: 2

Leaf Wetness Sensor

Brand: Davis Instruments Pages: 2

M-Class Mark II M-4206

Brand: Datamax Pages: 22

Brand: DataCard Pages: 2

CSL Elite Racing Wheel

Brand: FANATEC Pages: 2

Brand: FANATEC Pages: 8

Brand: FANATEC Pages: 35

Brand: Jetter Pages: 4

Brand: K&K Pages: 8

Brand: K&K Pages: 20

Brand: K&K Pages: 6

Brand: K&K Pages: 3

Brand: K&K Pages: 3

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands