Manitowoc AUCS Q Use And Care Manual Download Page 20

 

 

 

Installation Instructions

 

Section 2

2-12 

Determine Type Of Solution Needed 

 

 

CAUTION

 

Use only Manitowoc-approved Ice Machine 
Cleaner (part number 94-0546-3) or Sanitizer (part 
94-0565-3) in the AuCS

®

A It is a violation of 

Federal law to use these solutions in a manner 
inconsistent with their labeling. Read and 
understand all labels on the bottles before use. 

 

The AuCS

®

A accessory will dispense Cleaner OR 

Sanitizer. It cannot dispense both at the same time. 

 

 

CAUTION

 

Do not mix Cleaner and Sanitizer solutions 
together. It is a violation of Federal law to use these 
products in a manner inconsistent with their 
labeling. 

 

MANITOWOC ICE MACHINE CLEANER 
Part Number 94-0546-3 

Ice Machine Cleaner is used to control build-up and 
to remove lime scale or other mineral deposits. It will 
not “sanitize” the ice machine. 

It is recommended for use in places that have lime 
scale or other mineral deposits built up, but no 
problems with slime. 

MANITOWOC ICE MACHINE SANITIZER 
Part Number 94-0565-3

 

Ice Machine Sanitizer is used for sanitizing and 
controlling algae build-up (slime) and other bacterial 
growth. The ice machine should be sanitized on a 
regular schedule, following Manitowoc 
recommendations and local regulations. 

It is recommended for use in places such as pizzerias, 
bars, bakeries, etc., that have airborne bacteria 
(yeast). Sanitizing is also recommended in places that 
do not have lime scale (or other mineral deposit 
problems). 

Model 

Amount of Cleaner or 

Sanitizer Dispensed 

Q200  Q280  Q320  Q370  Q420 

Q450  Q600  Q600C  IB600C  

Q800  Q800C  IB800C  Q1000 

Q1000C  IB1000C  SU1000C  

Q1400C  

 

*2.4 ounces (70 ml) 

Q1300  Q1600  Q1800  QDUAL  *4.8 ounces (140 ml) 

*The dispense rate is automatically controlled 

Installing Bottle Of Solution 

 

 

WARNING

 

Wear rubber gloves and safety goggles (and/or face 
shield) when handling Cleaner or Sanitizer. 

 

 

 

CAUTION

 

Follow instructions listed under “Changing 
Solution Type” on the next page when changing 
from Cleaner to Sanitizer or from Sanitizer to 
Cleaner. 

 

1.  Place the bottle into the AuCS

®

A accessory. 

2.  Slide the tube to the bottom of the bottle and 

hand-tighten the cap. 

 

 

TUBE MUST BE CLOSE 

TO BOTTLE BOTTOM 

SV1645

 

Bottle Installation 

 

 

WARNING

 

Do not use 1 gallon bottles of Cleaner or Sanitizer 
on the AuCS

®

Summary of Contents for AUCS Q





























Reviews: