PRINTED IN U.S.A.
25
50960025/CP0514
A2 - Engine Coolant Temperature:
Press button “B”
until “TEMP” is displayed. It indicates the temperature
of the engine coolant. Under normal conditions, this
should indicate approximately 185°F (85°C).
A3 - Engine Oil Pressure:
Press button “B” until
“OIL” is displayed. This indicates the engine lubricat-
ing oil pressure.
A4 - Voltmeter:
Press button “B” until “VOLTS” is
displayed. This indicates the voltage output from the
alternator.
A5 - Hourmeter:
Press button “B” until “HRS” is dis-
played. It indicates the total operating time of the
machine and should be used for keeping the mainte-
nance log.
A6 - Maintenance Reminder:
After every 250 hours
a reminder will display: “ROUTINE MAINTENACE
IS REQUIRED
⎯
CHECK OPERATOR’S MANU-
AL.” Perform the required maintenance, and then clear
the message by pressing and holding button “B” until
the message is cleared.
NOTE:
The maintenance reminder message
must display at least three minutes before it can
be cleared by pressing and holding button “B”.
A7 - Error Fault Code:
Error codes and a short error
description are displayed in this screen. The error code
will clear when the error is corrected.
Indicator Lamps
C - Low Fuel Lamp:
This lamp indicates a low fuel
situation. The fuel tank should be filled as soon as pos-
sible.
D - Brake Failure Lamp:
This lamp indicates the con-
dition of the service brake systems. The front and rear
brakes are on independent systems. If a loss of pressure
occurs in either system during normal operation with
the brake pedal depressed, this lamp will come on.
Failure in one of the brake systems does not affect the
operation of the other system. However, the MANDA-
TORY SAFETY SHUTDOWN PROCEDURE (p. 8)
should be followed and any necessary repairs made
immediately.
E - Transmission Oil Temperature Lamp:
This lamp
indicates whether or not the transmission oil is at the
proper temperature. During normal operation this lamp
should be off, indicating that the transmission oil sys-
tem is at the proper temperature.
IMPORTANT:
If this lamp comes on during nor-
mal operation, a problem may exist in the trans-
mission oil system. Stop the machine immediate-
ly and investigate the cause of the problem!
F - Engine Pre-heat Indicator Lamp:
When lighted
this lamp indicates that the cold weather starting aid is
in use.
G - Alternator Lamp:
This lamp indicates the condi-
tion of the electrical charging system. During normal
operation, this lamp should be off. If the charge rate is
too high or too low, this lamp will come on.
H - Coolant Temperature Lamp:
This lamp indicates
if the temperature of the engine coolant is too high.
IMPORTANT:
If this lamp comes on during nor-
mal operation with the engine running, STOP the
engine as soon as possible and check the engine
cooling system.
I - Engine Oil Pressure Lamp:
This lamp indicates
whether the engine lubricating oil pressure is suffi-
cient. During normal operation, with the engine run-
ning, this lamp should be off. During starting and when
the ignition is on but the engine is not running, this
lamp will be on.
IMPORTANT:
If this lamp comes on during nor-
mal operation, stop the engine immediately! After
allowing the oil to drain down for a few minutes,
check the engine oil level. Maintain oil level at the
FULL mark on the dipstick.
Exhaust Filter Gauge Indicators and
Switches
A - Exhaust Filter Cleaning Switch:
This switch con-
trols the function of the exhaust filter. It has 3 positions
as follows:
A1 Center position:
In this position the exhaust fil-
ter cleaning procedure is set to the automatic
(AUTO) mode. Operating the engine in this cen-
ter AUTO Mode allows the ECU to perform intel-
ligent exhaust filter cleaning as required.
B4
C
A2
A3
B2
B3
A1
B1
