background image

2-32

F - DIRECTION SELECTION SWITCH

  Before selecting one of the three possible steering positions, bring all 4 wheels into alignment with regards to 

the lift truck axle. Never change the steering mode whilst driving.

F1 - Front and rear steering wheels in opposite directions 
        (Short or concentric steering).
F2 -Front steering wheels (Road travel).

F3 -Front and rear steering wheels in the same direction 
       (crab steering).

*Wheel alignment procedure:
Press the steering mode selection switch on 

“

F1

”

, turn the steering wheel until the rear wheels 

are aligned A2, press the steering mode selection switch on 

“

F2

”

, and turn the steering wheel 

until the front wheels are aligned A1.
When the front and rear wheels are aligned, one of the three steering modes mentioned above 
can be selected.

The wheels coordination may be lost with use; carry out realignment of the wheels every 20 hours 
of service by following the procedure described above.

  Before driving on roads, it is necessary to check the alignment of the rear wheels and to drive in front wheel 

steer. The control of the alignment of the rear wheels must be regularly done with the help of the green lamps, 
while driving the lift truck. In case of anomalies, consult your dealer.

G - CONCENTRIC STEERING GREEN LIGHT

The green light indicates that concentric steering is selected.

H - LATERAL OR CRAB STEERING GREEN INDICATOR LIGHT

The green light indicates that lateral or crab steering is selected.

K - SPEED SELECTOR (SLOW-FAST)

The machine can run at two speeds:

- Slow (for work site)
- Fast (for road travel)

To change the speed, follow the instructions given below:
- stop the forklift truck movement completely
- keep the i.c. engine running at minimum speed 
- position the reverse gear in idle (see point)
- push the brake pedal all the way and press the slow-fast pushbutton 

“

M

”

 until the 

  respective lights 

“

L

”

 or 

“

M

”

 light up.

If the forward/reverse movement is not activated, follow the instructions given below:
- position the reverse switch as required (Forwards - Reverse)
- discharge pressure from the brake pedal
- Press the 

“

F

”

 

“

TRANSMISSION RESET

”

 pushbutton to obtain the connection in the 

  required direction.
- If the vehicle does not move, start accelerating the internal combustion engine slowly and 
  gradually until the truck starts moving.
These indications must be followed for proper working of the transmission.

L - SLOW SPEED GREEN INDICATOR LIGHT

The green light indicates that slow speed is selected.

M - FAST SPEED GREEN INDICATOR LIGHT

The green light indicates that fast speed is selected.

N - OPERATING MODE

Activating the two-position switch will activate the operating system concerned to work slowly 
and accurately.
The switch can also be turned on with the lift truck in motion..

F1

F3

F2

F

H

G

A2

A1

A

M

L

N

K

K2

K1

PDF created with pdfFactory Pro trial version 

www.pdffactory.com

Summary of Contents for MHT-X 780 T-E3






















Reviews: