To receive Freesat
you must
connect your Plaza HDR•S receiver
to an appropriate satellite dish,
fi xed in position and accurately
pointed at 28.2° East satellite
position.
For safety reasons and to
provide reliable reception,
we
strongly recommend that the dish is
professionally installed. If you have
any questions about the dish, please
consult your installer.
2
CONNECT TO A DISH
Place your Plaza HDR•S receiver
on a fi rm, level surface close to your
television, a mains electricity socket,
and the cables from the dish.
Connect the cables
from your
dish to the LNB IN 1 and LNB IN 2
sockets at the back of the receiver.
Make sure your television is turned
off
and connect the HDMI cable to the
HDMI socket on the rear of the Plaza
HDR•S and to an HDMI socket on your
television. If you need more guidance,
check your television manual.
Connect the +12V DC connector
to
the 3A DC 12V connector at the back
of the receiver. Then connect the
Power Supply Unit (unit with 3 pin
mains plug) to an available mains
socket that is turned off.
3
PLUG IN
Remove the battery compartment cover
from
the back of the Plaza HDR•S remote control
by lifting the cover catch. Insert the two AAA
batteries supplied, as shown on the inside of
the compartment. Replace the compartment
cover.
Turn on your TV set
and choose the HDMI
input (see your television manual).
Switch on the mains socket
the Plaza HDR•S
is connected to. After a few seconds, step
one of the Freesat installation process will be
shown on the television screen.
If you do not see this screen (pictured
opposite), please refer to the
Troubleshooting
section in the main user guide
.
4
SWITCH ON
When the fi
rst installation screen is
displayed,
use the or buttons to select
the screen format of your television (16:9
Widescreen or the squarer 4:3 Traditional).
Press the
button to highlight the HDMI
Resolution selection box, and then use the
or buttons to select the correct resolution
for your television (see your television’s
manual for guidance, or select 720p if unsure).
Press the
button
to highlight the “Next”
box and then press
again to display the
next installation step.
The signal check is successful
when both LNB
inputs are receiving a valid signal. If it fails, please
see the Troubleshooting section in the main user
guide. When the fi rst input is connected to a valid
signal, the “Next” box will become highlighted.
Press
to display the next step.
Enter your postcode,
pressing the number
buttons an appropriate number of times
to produce the letters (printed above each
button) and numbers required, in the same
way as ‘texting’ on a mobile phone. You do not
need to enter a space. If you make a mistake,
the button deletes the previous character.
Press
to confi rm the postcode and then
press it again to display the next step.
Your Plaza HDR•S receiver
will take a couple of
minutes to fi nd and store the Freesat channels
available, displaying the total number of
Freesat TV and radio channels found. Press the
button to display the next step.
Enter your choice of PIN
(used to unlock certain
channels and functions) by pressing the required
number button (0, 1 … 9) for each of the four PIN
digits. Press
to display the next step.
Setup is now complete.
Your PIN will be
displayed on-screen along with a reminder to
take a note of it. When ready, press
and
enjoy watching Freesat TV.
5
TUNE IN
DO NOT OPEN
RISK OF ELECTRIC SHOCK
DC 13V
3A
TV SCART
VCR SCART
ETHERNET
USB
HDMI
300mA max
LNB IN 2
300mA max
LNB IN 1
AUDIO
R
L
S/PDIF
OPTICAL
Cover catch
To watch On Demand TV services
including BBC iPlayer
and ITV Player, the Plaza HDR•S must be connected to your
internet router or hub using an ethernet cable (not supplied).
Plug one end of the ethernet cable into the ETHERNET
socket at the back of the Plaza HDR•S, and the other into
your hub or router. Make sure the connections are fully
pushed in - you’ll hear a click as they lock into place. Consult
your router or hub’s documentation for further guidance.
