M&G Duravent Duratech Canada HT Installation And Operation Instruction Manual Download

Page: 1 / 16

PIDURATECH REV. 2 07/2013

URA

ECH

ANADA (DTC)

Factory-built CHIMNEY

5”, 6”, 7”, 8” & 10” dia.

TYPE HT

INSTALLATION

AND

OPERATION

INSTRUCTIONS

Read these instructions and keep them for future reference

Listed: CAN/ULC-S629 (6’’,7’’,8’’ only)

CAN /ULC-S604

UL-103HT

Duravent

www.duravent.com

SUMMARY

OUR PRODUCTS LIVE UP TO OUR NAME, WARNING. . . . . . . . . . . . . . . 2

KEEP YOUR CHIMNEY CLEAN, SIZING CHART . . . . . . . . . . . . . . . . . . . 3

GENERAL INSTALLATION NOTES. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

INTERIOR STRAIGHT INSTALLATION WITH MULTIPLE FLOORS . . . . . . . 5

INTERIOR INSTALLATION WITH CATHEDRAL CEILING . . . . . . . . . . . . . . 7

OFFSET INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-9

EXTERIOR INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-11

INTERIOR INSTALLATION ON A FURNACE & WATER HEATER . . . . . . . . 12

SPECIALIZED COMPONENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

WARRANTY. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Summary of Contents for Duravent Duratech Canada HT

















Search results

Summary of Contents for Duravent Duratech Canada HT

Reviews:

Related manuals for Duravent Duratech Canada HT

Brands by name

Popular brands

M&G Duravent Duratech Canada HT, Installation And Operation Instruction Manual

Search results

Summary of Contents for Duravent Duratech Canada HT

Reviews:

Related manuals for Duravent Duratech Canada HT

Brands by name

Popular brands